What have you done to your 2.5 gen Tundra today?

Yep

 

I asked AI to make my wife’s Sequoia.

 

That's so cool!

 

I have a 16 & it doesn't have TSS. I'm 99% sure TSS started with the 2017's....if that's the case then a 16 grill wouldn't have the cutouts/mounting bracket or whatever for the TSS sensors that you have on your 2017.

 

That wasn't until 2018, 2014-2017 are the same grill

 

I've been running a set of these in bronze since August of 23, they've been a great wheel for me so far.

 

Test, tune, repeat.

 

Yuhp... lights work good!!!!

 

Pretty sure this was on low lol

 

You are blessed to live in such an area! How does trail maintenance and stuff work. Or does it just turn into what it turns into?

Thanks!

 

Well I’m in Vegas for work and have family here so if I can I drive down from Oregon. These are trails no maintenance etc they are what they are. This is just around the corner from the in-laws and hundreds of miles of trails to test the truck and dial things in.

 

Alignment and re-balanced the wheels and tires.

 

Caught him mid act two weeks ago. Big little bugger. HOWEVER I have found a solution, knock on wood, Moth Balls. I used chicken wire and made little rectangles with foldable tops that fit 10-15 moth balls in there. I put one near the battery/fuse box and another near the intake. I also crush a few up and throw the powder under the truck and around all 4 tires. Hopefully in 12-16 months I'll be moving out of the HOA and away from these rodents. But moth balls have been working and best part is, they don't break/wash away when it rains. The ones I threw on the ground are still there after 2 weeks.

I still have 1 ⅝ inch driver side lean with the King 3.0's on the front - same thread on pre-load, spoke to kings twice. First time the guy said learn to live with the lean lol and then second time they are sending me a new upper collar without pre-pressed in bolts, should allow me to get longer bolts to slide 1 or 2 shims in there to get my height back. Stock bolts won't give me enough room for a shim and get the top nut on a few turns. We shall see. Aside form the lean I love them.

 

Little fucker ! Actually had one fall out from underneath when we were pulling into a parking lot

 

2 minutes into cleaning the interior for the 1st time in a long time and I've already found $10 and a full pk of smokes.
This could get pretty interesting, no idea what I'll find in here.

 

Anytime I clean my interior I find melted skittles and potato chip crumbs. Dang kids.

 

Hahaha the struggle is real!!

 

i usually just end up with a shop vac full of dog hair, like enough to build another dog or 2. LOL

 

I've got a lightbar that's about 3 feet long. It's great when it's raining really hard or I need to blind someone. Ha ha ha

 

Sure, the kids.....riiiiiight...

 

That's a lot of hair! What kind of dogs do you have? I have a black Lab. He is in my avatar. He's my buddy. Jasper is his name.

 

ever watch initial D?
https://youtube.com/shorts/T9o2DeNtKhk?si=DbPTJ3DFwRBQ33dV
AE86!!

 

Lol, no, no I haven't. I don't really blind people. Not on purpose anyway.....

 

I had them on my 22. No issues at all. Well worth the cost compared to OEM if your OK with the offset.

 

if your into anime and race cars i highly suggest you check it out. such a great series

 

deer head chihuahua, shes my road dog.

 

the fruit loops sent me, it was all good till i saw that, now i cant stop laughing at it.

 

I bought an Amazon special battery mount and machined to fit !!! $10 and 10 minutes of my time.

 

so i really am the only guy using wing nuts on my battery tie down? these are my roadside wrenches. LOL

 

Ok, so here we go again... and yes, I know I assured a few of you a week or so again that I was going to be happy w/just blacking out the chrome part and leaving the gray in place, but..... I'm not

So, when I did the console, originally I had just replaced the cup holder trim and snapped on a blackout piece of the chrome zig zag thing in the shift gate area... But, I didn't like the contrast of having the one gray piece in the console, so I ended up swapping that piece as well. Now I feel the same about the gray surrounding the Head Unit and HVAC controls...

Anyhow, my question for you folks is this.... Am I smoking dope here, or did I see a post somewhere w/someone replacing those 2 pieces w/OE parts from a different trim level/vehicle model, and if so does someone happen to have the OE part #s for those 2 pieces.... or, is my only option to use something like Meso or AJT parts???

PS>> Yes, I know I can paint them... But I hate painting, and I'm not very good at it; it's really a matter of patience...