WHAT HAVE YOU DONE TO YOUR 3RD GEN TUNDRA TODAY?

Mustache is now same body color and got the Garmin PowerSwitch installed.

 

Installed a Lomax Tonneau cover, Black Armor bed mat, the Spigen Matt glass screen protector , JDMCAR console piece over the gloss, and a couple of Cup Grips.

 

Installed Tonno Pro tonneau cover.

 

Spigen is a must have, improves the screen 10 fold by getting rid of glare

I wish someone made a complete replacement trim for the center console to get rid of the piano black. I clean it, and 10 seconds later, dust ball. And dont dare touch it, scratches just looking at it.

 

https://www.ajtdesign-llc.com/online-store/Center-Console-Panel-2022-Tundra-BLACK-p623594337

 

ProTech makes a clear film that goes over the piano black, makes it look new with no scratches visible and looks clean all the time.

 

BFG AT KO2. The lift is a 3/1" level from readylift. I need to figure out how to fix my wheel articulation though, turning is awful after the change.

 

Anyone know if there is a protective film for just the speedo area? I already applied the 14” screen cover a couple years ago. But have not been able to find just the speedo (only found in packages with 14”screen)
TIA

 

Thanks, but it wont work for me.

 

Maybe I just put the matte black over it, just not to sure about anything stick on. Thanks!

 

What method did you go for the mustache? I’m debating between ordering a whole new one through oempaintedparts or just doing the bumpershellz. Wrapping it isn’t an option because I can’t find lunar rock vinyl anywhere.

 

Installed this beefy thing.

 

Oem trd pro grille with oem marker lights and rave off-road light bar got put on today. Love the look!!

 

Looks great! I'm doing the same thing tomorrow morning

 

Fabricated a fuse block bracket and mounted a Blue Seas 6 circuit fuse and 100amp breaker/ master cut off switch. I didn't feel like paying $70 - $130 for a piece of bent plate steel so I bought an $11 1ftx1ft 28 gauge steel from HD and cut it out with an angle grinder, bent it like origami in a vise, painted it with high temp spray paint, and drilled all the necessary holes. I had a 4 prong relay bracket laying around and bolted that on. Used some RTV black silicone sealant to seal the holes I drilled in the fuse box lid to mount the bracket. This was a $50 project

 

What brand is that?
Been waiting 2.5 months on my srq/true north version

 

Looks great. Is that removable to get to inside the fuse box underneath?

 

Talon. I purchased the same one about two weeks ago and it arrived within a few days. They are also a site sponsor.

 

Great minds think alike?
(although I just used some VHB tape to mount my BlueSea)

 

Very nice work. Definitely doing something similar. Thanks for the inspiration.

 

Hopefully finally take delivery of the truck from the dealer after 3 weeks.

 

Looks great. Is that body colored fog light bar OEM, wrapped or aftermarket?

 

Thanks! It’s body color painted oem part. I ordered it from paintedoemparts.com

 

Excellent, thanks and it looks really good. Last question - how was the install of it?

 

It just comes off with the fuse box lid

 

Came up with a simple solution for my EZ-Pass since the Rubigrid is in place. Used some magnets I had in my toolbox. Also cleaned up the cord earlier this week.

 

Stealing this idea, this looks great!

 

Can you supply a link where you bought the console piece? TIA!

 

Phase 2 of operation voided warranty, potato pic for plausible deniability
VF tuner 93 octane +TCU maps, allegedly…

 

Well the VF Tuner once removed is supposed to be undetectable so it won’t void warranty if you remove it prior to service.

Not sure about those maps, I thought the reason for a box like a VF Tuner was to trick the ECU since its locked?