What have you done to your 2.5 gen Tundra today?

Does me no good. I don't have a crew max.

 

Hell I went to TR High School.

 

What years?

 

how much chopping?

 

Look at this guy, flexing level ground like that!

 

Minimal - just had to cut the fins off the front of the wheel well cover and then just shove that inside the bumper.

 

Can anyone recommend decent fog light bezels?
Found these on the cheap, anyone used em?

$16 For Toyota Tundra 2014-2021 Fog Light Bezel Passenger Side | Front | Made of Plastic | Replacement For TO1039175 | 521270C070, 615343558653

https://www.amazon.com/2014-2021-Pa...=&hvlocphy=9030104&hvtargid=pla-2281435177818

 

93-96

 

Simple one today. Velcro Molle panel for the passenger visor. Need to find my glow monster patch from @ToyoMafia though.

 

Appreciate it, but I'll pass... The truck isn't a DD and I haven't used the cooled seats much in the past.

 

Id be interested in it if you want to sell it.

 

Gotcha. I graduated in 91.

 

Modded the console lid to open further as its always a pain point fighting with it to get to stuff with my seat position.

https://www.tundras.com/threads/console-lid-mod.44686/#post-1148497

 

Got rid of a little chrome and and that weird silver trim in the Pro last night...

Building the console:



Console installed along w/an all black w/red stiching TRD shift 'knob':




Last addition was blacking out the chome Toyota emblem on the steering wheel:



PS>>> Anyone else here think the tow/haul indicator on the dash display should be green and not yellow

 

My center console mod

 

Did you paint the steering wheel emblem?

 

Any suggestions or pointers on how to get that whole center console piece out?
I have been trying, lack of full destroy, to get it out to get the chrome off, but failed.....

 

That's slick. Details on the charger you used?

 

Got stuck behind a guy who was beating the hell out of his rogue. Anyone know how I can get the smell of a cooked CVT out of the cabin?

 

No sir... It's an overlay that is part of an original AJT kit that I picked up recently from another forum member here. It is my understanding that AJT can no longer produce them after a C&D from Toyota...

 

I ordered it off eBay it's the magnetic charger that holds your phone in place when you use a magsafe case.This bad boy taps into the 12v plug on the rear of the console while allowing it to still function.Its one of my favorite mods.Easy to install, simple wiring and only works when the switch is on.

 

Sorry... are you talking about the whole center console piece that was show in the pic above, or are you talking about pieces within the whole center console piece??

 

Well crap I guess painting is my only option

 

I'm guessing that's gonna be a bit of a bitch to paint....

Quick search of the internet produced these two options....

https://off-roadautoparts.com/produ...fk227DNUUlXcH3j872HvxF--7SvgWaUMaAuf9EALw_wcB

https://yotaxpedition.com/products/...n2zRvqRJMPuXMR15usQIysKq31GYYXBQaApQ5EALw_wcB

 

The whole center console piece, I have the AJT kit but can't get it the piece off to even start on the replacement.....

 

Thanks. I've got one in my Taco but where's the wire on yours? Rear exit?

 

Just ordered one from Yota.... thanks

 

It taps into the 12v wire for the rear center console accessory plug

 

Copy...

Open your center console lid;

Then, using a new or undamaged plastic pry tool, start by popping the corners of the console up that would sit under the console lid (armrest), and then work your way around...

I find it's easiest to slide the tool in under the part that's not normally visible in case in cause any scuffs or damage. Then once the tool is inserted, slide it until it bumps into a 'tab' then twist the tool left or right (rather than trying to pry). Slide it again to the next tab and then twist again. Once you have a couple of tabs 'popped' it's pretty easy to just work your hands around the console and then apply firm stead pressure upward at the tab points to pull it the rest of the way up. Rubber gloves help keep your fingers from slipping as you're working and provide a little more leverage.

Also, note: You will need to remove the shift handle (knob) by unscrewing it counter clockwise to be able to remove the console.

Here is a photo of the underside of the console showing where the yellow tabs are located for reference:



*** This second photo shows were the 3 clips are that sit under the console lid. Easiest to pop one of the two corner ones first...




If that doesn't work, the next easiest one to pop would be the one in the top photo's upper left corner, which is the upper right corner if the console is face down in position.