What have you done to your 2.5 gen Tundra today?

Milkshakes are a must when eating a Wendy's or 5 Guy's burger.

 

Swapped out the chrome grille, hood bulge, & bumper end caps.

Before:


After:

 

That black grill looks real good

 

Thank you

 

More better!

 

Nice. All my supplies finally arrived so I'm ready to do the difs and transfer case as well. This weekend and the next are a little busy so hoping to tackle mine on 4/5. Good luck!

 

Looks nice!
Do you happen to have the part numbers for the bumper end caps? I’m looking at doing something similar.

 

Getting the newer AT4’s in the same size. Would’ve done another set of the AT3’s if I could find them.

Thailand.

 

I had 1 bad new falken at4w that was causing vibration between 60-70mph. They replaced it with a new one and all is awesome. Tires road so nice on the road and was darn good in the snow and ice.

 

RAS works really well. Have had it on for 2 years. No regrets.

 

Gave it a bath, I’ll wash the sequoia tomorrow

 

Thanks man

Left: 52113-0C908
Right: 52112-0C908

 

Drivers side installed tonight, definitely an upgrade on what the previous owner had installed.

 

Any discount code for bumper shellz on ecological.com??? Thx

 

TUN10 is the forum discount code.

 

Is it just the picture or does the Sequoia have a long hood?

 

Thanks

 

Approved vendor here, so send over a PM and see if they are running any specials or forum discounts...

 

Angles plus new phone camera tech = swoll...

 

I got tired of stuffing a towel into the passenger seat cushion since I've got pups riding in the Pro now, so I installed some WetOkole seat covers tonight... I think they came out decent, but good lord I'd rather lay on my back on the asphalt w/a set of skids or a slider balancing on my lap than stuff my hands under the front seats.... Sharp crap everywhere under there. Driver's side wasn't too bad, but the passenger side was a beeeooootch, especially with the JBL DSP aftermarket amp and all the extra wiring and connections under there. The board that James mounted those amps on really doesn't lay flat under there and takes up almost any clearance. One of these days I'm going to have to get under there and clean that thing up...

Moral of the story, save yourself a little time and torn flesh... Just pull the seats out, wrap em up in whatever covers you choose and reinstall them. Probably would have saved me an hour and a bunch of small cuts and abrasions had I gone that route...



I'm sure the neighbors loved the occasional f'bomb at 0200, but hey this is when I shine!!!

 

Polished SCS Ray 10’s on quicksand. Can’t imagine there’s anyone else with this combo is to why I did it. Anyone?

 

What camper?

 

get some eBay seat jacker, it will give you more clearance. I have a set and now there’s plenty under the seat. I also have 2 amps under the seat. It was a tight squeeze before.

 

I have DDI seat jackers on the driver's side, plus that seat powers up and down. The passenger side is only a 4-way power seat, and the wife didn't like the seat angle w/the seat jackers installed, so....

 

We're staying at the Lake Powell Resort and camping (sleeping) indoors... floating the Colorado today.

 

Bummer. I took my side off because i’m too short even at the lowest height setting and it was causing discomfort. But left the passenger side in. Wife usually sit in the back with the kiddo so no feedback, yet.

 

white glass those were the days

 

Long live the Orca!

 

Been there man.
Doesn't matter the vehicle brand either, I've been sliced and diced several times

 

New to me 2020 1794 low miles minty. Adding Slee sliders; here are before and after. Able to do it all myself on soft ground and without experience or good tools. Next up some BP51s, bronze icons, 34s. Maybe some Nacho lights...