WHAT HAVE YOU DONE TO YOUR 3RD GEN TUNDRA TODAY?

Installed the @Talon2006 engine skid plate. Took me about an hour. Instructions could use improvement but otherwise I think it’s good to go. Lines up well with my Miller Cat shield.

 

New shoes. Feeling cute, might delete later.

 

Out with the "Paw-Paw steps" as my daughter calls them and in with the much better-looking (if albeit less functional) Predator drop steps.

The rail-to-body gap is wide enough in the rear to almost stick your finger in between, but it is within 1/4" on the front. There is no adjustability. Can anyone confirm theirs is the same?

 

Finally got this “premium” sound bumping. This solution plus the beatsonic amplifier add on totally transformed how the truck sounds. Highly recommend as a cheaper alternative to replacing the entire system.

1.5 boxes of secondskin 2mm sound deadening
4 hush mat speaker pads for the doors
Foam sticky tape (retaped the door panels in addition to the factory)
Foam behind stock subwoofer and foam tape around the plastic panel where it meets the outside rim of the subwoofer.

 

Got the ppf and ceramic coating checked up on and cleaned. Also got the paint matched fog lamp bezel installed / ppf’d and ceramic coated. Love the look now. Next up, trd pro grille with marker lights and light bar!

 

Probably shaking loose some air pockets.

 

Haha is that a 10mm rolling around in there?

 

I added ditch lights (amber dashes on each side) to my new bumper and needed a switch. I got an OEM style switch off Yota Verse but it was a little bit of a hassle to use the lower left square that was blank on my dash. The others were very easy before. I explain it on my build page if anyone plans to use that blank location as it’s different than the rest

 

Waiting for the shop to schedule my PPF maintenance, they are doing 20 ceramic on the roof then. I am going to have them do the windshield in 70 as well. A lot of truck mods in the works, just waiting for parts to be fabbed up.

 

Finally!
Been wanting to utilize that blank spot. Yes please explain how.

 

Mine are the same. The gap slowly shrinks from rear to front on both sides. It drives me nuts trying to clean in there towards the front.

 

Yeah, gonna top it off again

 

It was kind of a hassle since the blank they put in that end spot is different than the blanks I had in the lower row. Those lower row blanks to the right were very easy and the new square switches dropped right in. Because the left blank is bigger I had to cut the end off and slide the switch inside the chopped blank. It worked pretty well, but still a hassle.
https://www.tundras.com/threads/off...tion-mods-on-37’s.105476/page-12#post-3877887

 

OK, thank you sir for confirming. I loosened the bolts to see if there was any wiggle room and there is only maybe 1/8" in either direction - the bolts are pretty close to the same size as the holes so there isn't much there to shift the rails around.

 

And the big question, does this charger work with phones with a case??

 

Works on my S22 Ultra with a Spigen case

 

Works on my s23 with otterbox case.

 

Front windows tint matched

 

been a little over 1k miles since the new engine....dumped the oil a few days ago so installed the JB4 and E85 sensor last night...back to scootin off every stop

 

How is it doing? Do you think the way the guy in the video and the way you did it are better than flipping it the other way like he says you can do?

 

Bought the pro grille to switch out but it didn't come with the backplate and letters anyone know where I can buy this piece? I can't seem to find it

 

Backplate and letters? Have a pic?

 

Prolly some temu special

 

What? Where?? Lol

 

When the photo was small I thought that was the reflection off of a socket

 

That’s what she said.

 

Worth removing and drilling the holes bigger?

 

sounds like you ordered a knock off or a Tacoma grille.

 

Front door tint looks so much better. I’ve been meaning to do this for the past 1.5 years, lol