What have you done to your 2.5 gen Tundra today?

Never been so lucky to have a $100 gift card to Amazon. Pretty sure it'd go in record time

 

I only had it cause they give you one when you open an Amazon credit card. It was burning a hole in my screen so I had to use it.

 

You got a part number on those? They were the bane of existence when I was a tech, I'd love to delete them...

 

Ah ok then I think I got one at some point

 

More like the wife got it lol

 

Haha not a chance. We have separate accounts on everything

 

I’m due (overdue) for a rebuild on the TRD Pro shocks.
Since it’s my daily driver, I can’t be down for the time it takes to send them in for rebuild, so I have to swap in something at least temporary for that time period that has the same amount of lift and clearance for my tires, etc. The price of a second set of TRD Pro’s is substantial, and there’s a few other tweaks I’ve been contemplating anyway so, in typical fashion I have decided to double down and overhaul all of it while I have it apart…

Icon RXT leaf pack (currently planning option 1)
8112’s up front, 8100’s in the back
Icon billet UCAs
CB tie rod kit
CB front shims (to keep the 3” lift and keep the 8112’s “in the zone”)
Keep the RAS
Keep the 2” CB rear shackle (aiming at about 1” rake when empty)
New brake pads and fluid change (hoping I don’t have to replace pistons, and still deciding what rotors)
Upgrade to SS brake lines
1” Bora wheel spacers for just a touch more width and UCA clearance (not letting go of the BBS wheels)
ABS sensor guards

 

Sumo springs..Got the CAI direct from Shillen and accelerator from Toyota

 

Gotcha.

 

Installed some air bag helpers for when towing the toy hauler. And the diff breather relocation to behind the tail light housing.

 

There’s only 2 models of the Stillen. Dry or Oil and with or without block off plate for water seepage.

But can confirm that TRD intake accelerator does fit nice and snug with the Stillen air box.

No modifications needed.

 

You got in in without trimming the intake tube on the box didn't you?

 

Filled the power tank and cleaned the rig up, added a few more recovery gear items.

 

Just some Hawk Tuah probably

 

The ARB kit is nice. I’ve got mine routed up front into the engine bay.

 

Yessir! Didn’t trim or cut anything. The only PITA was the top 10mm bolt with the bushing holding the box in place. I’m going to have to remove it and replace the bolts since it’s rusty.

Gotta also anti-seize everything.

 

That kit is definitely nice. Thought about running it to the front too, but I think this will suffice.

 

Nice. I ordered the accelerator from Amazon since the dealer never called me back. At least I'll know it will be here in 2 days. Did you ever find the replacement bolt part numbers?

 

LOL

 

Does this look like it is a part for the Tundra? Found it laying on the ground in my driveway. Close to the driver side rear bumper. Looks like a cap with foam inside.

 

Looks like something that probably rolled down the street from someone's trash can or something kids could have been playing with.

 

It's the filter for the blinker fluid.

 

Found the same exact thing on my garage floor years ago lol. It sat on my toolbox for years after. Never figured out what it was for.

 

Not likely considering where I found it.

 

Yeah I did! It’s about $6 a pop.. hopefully that’s what shows at the parts center.

 

Thanks for the heads up on the discount.... Applying a 10% discount to my order.....YES

 

This is nearly what I’ve settled on, except I was thinkin Deavers in the rear and JBA UCAs.

Bilsteins, Boras, RAS, etc. Yep!