2014-2021 Front/Rear Anytime Camera Mod - FRAC Harness

TundraTex

Does this change anything from being out on the list and just you having to send an invoice?

 

@SpeshulED, being on the list means you were tagged in the notification and ordering instructions in post 437. It also helped me figure out how many harnesses I needed to build for the first round. If you want to seal the deal and complete your order, e-mail me the information requested in post 437 and I'll send you a billing invoice. Hope that answers the question.

Thanks.

 

Hey Tex,
Did you started shipping them yet and how do we find out where on the list we are?
Sorry not trying to be pushy just anxious.

 

Guys,

The first round of harnesses will be shipped tomorrow, and I anticipate that all current orders will be shipped this week. I really appreciate your orders, support, and patience! If you ordered a harness and have not yet paid your invoice, please do so now. I can only ship paid orders. If you think you ordered and you haven't seen an invoice, it's possible that it went to your e-mail SPAM folder, check there. If you still can't find it, contact me at the e-mail provided in the ordering instructions (post #437) and I'll re-issue an invoice. If you haven't ordered a harness, and you want one, now is the time to do so!

Based on multiple requests, I have updated the installation instructions to include information for an alternate installation using the Switch-Pro panel. I will be e-mailing the installation instruction document to each buyer at the billing e-mail address you provided for your purchase. It's also attached below.

Thanks again for your support!

Lou

 

did anyone find a good camera to use on a TRD pro grill? (mine has been sitting in my office for 3 weeks now - i promise i'll get around to installing it one day)

 

Payment sent. Sorry for the delay. Thanks Lou..............

 

Shipped out a dozen FRAC harnesses today. If you got an e-mail from me with your tracking number, your FRAC harness is on the way. If you didn't get an e-mail, your FRAC harness is still getting its finishing touches and is in queue for shipment later this week!

 

Tundratex how do I go about getting one ordered up?

 

Got the email. Thanks.

 

I might have found an alternative.

The one you pictured looks a little big for the area I'm thinking. It looks like it would stick out pretty far.

 

I can take a picture of mine (I have the one @TubdraTex posted) so you can see how far it sticks out

 

@blue16 check back a couple pages in this thread to post #437. All the ordering information is there. Let me know if you have any problems finding it.

Thanks

TundraTex

 

Since the harness is a-comin' pretty soon, I mounted and wired up the camera today.
One question I had was with getting through that passenger side grommet.

I noticed that the front of it has a wide slit, but is pretty closed up behind

Do you just punch a hole through the back of the grommet? Or if I remove some electrical tape then maybe everything just loosens up?

 

there are rubber nipples (as @TundraTex calls them....i call them something else.....they arw deformed nipples imo) in the firewall.....you cut the bottom one off and feed the wires through there. let me see of i have a pic....

 

I dont have a pic but can get you one in the morning if you can wait that long....

 

not sure where you are looking to lount but this is how mine looks...

 

Yes I do see those giant nipples. One above and one below. Ok, sure I'll just cut that bottom one off.
Anyway, I believe they say one can do just fine with just one nipple.

 

Lol i cut the bottom one.....you will need a hanger going through the floor inside the can through where you cut the nipple....then connect the wires with some tape to the hangar and gently pull it through....like you're caressing your girlfriend....not man handling a bad guy

 

Hey, you got your line in!

 

Oscar, The inside opening is a little smaller than the nipple side, so it also helps to cut a small X on the inside hole. Also use some silicone, or lemon pledge, or something similar on the cable when you feed it through. It helps keep the binding against the rubber grommet to a minimum.

 

sort of lol

 

Send you an email @TundraTex to support email address you provided with the instructions.

 

Hmmm... I don't see it yet.

 

I tried that one first and didn't like the look and changes it for a lower profile one.

 

I barely notice it and nobody else seems to see it either

 

Do you have a link to the lower profile camera? I have the first one pictured and not crazy about the look either.

 

What's view like on it? definitely post the link up for it. I'm sure there are quite a few who would be interested

 

I actually order it from China through eBay ordered it on September 19th ad received it on the 25th. $21.11 Plus free shipping.

I placed it on but my FRAC Harness won't arrive until later on today. I will be doing the install Friday or Saturday and update you guys on its field of view. I attached the link for it below

http://www.ebay.com/itm/371515955301

 

I like that one. If mine ever dies, I might have to replace it with that.

It will be interesting to see if the Field of view changes much.

Tex

 

Here is the picture of what it looks like. I'll be using a hot glue gun to hold it in place