WHAT HAVE YOU DONE TO YOUR 3RD GEN TUNDRA TODAY?

Got my TRD amber marker lights and Diode Dynamics light bar hooked up to their own CaliRaised switches. I previously had the marker lights tied to ignition, but I wanted more control.

Several videos online have guys running the harnesses through the cowl, but I ended up zip tieing it to the bottom of the cowl instead. Didn't want to mess with getting too close to the wiper arms, etc. A little less clean but everything is up and out of the way.

 

Wondering if the factory plugs for the foot well lights are there in the trims that didn’t come with them?

 

Easy enough to check. Just pull out the passenger side top panel and take a look if the wiring is there. I say the passenger side because it’s slightly easier to pull out.

 

Tufskinz letters and hitch cover.

 

https://www.tundras.com/threads/trd-pro-light-bar-switch-p-n.116422/

 

Nice foot well lights! Were they direct replacements for the oem’s or did you have to do something special (relay)?
Also, could you please tell us where you got them?

 

Hope this thread isn't just about "upgrades"



Didn't get as dirty has my buddy's 2nd gen but still got a lot of mud on my steps and undercarriage with a few scratches here and there. I'm gonna have a hell of time cleaning...

 

Get some 0 offset wheels and AT tires and try it again. I am sure you can get just as much mud on yours with pokey wheels!

 

Let's see those pics!

 

+1

 

They are from VLEDs. Not direct from plug in replacements, but pretty close. They sell pigtail kits that clip on to the factory wires. Pretty easy to install.
Here are the ones used for the front. Color is 5500k pure white
https://www.vleds.com/shop-products/light-bars/bar-21-se-w-c.html

And for the rear I ordered these… I’ll upload pics of rear once I get them installed
https://www.vleds.com/shop-products/pod-lights/pod-3-w-5500k.html

Also orders 2 6ft cables for connecting the rear to the front lights and a 2 way adapter to connect the 2 rears together.

 

Which recovery points are those on the front?

 

1 - Price, Service, Fit and use. All are great. I have one in my Taco as well. It is great for knees and for keeping stuff in place. They look great but you can still throw dirt and mulch in the bed. Just wash it out.
2. / 3. /4. The dividers are one 2X6X12 kiln dried fir cut in half, cut to size per the dimensions in the manual, and then trimmed to fit (about another quarter inch) for the bedrug thickness. I just cut it 1/8th inch at a time and checked the fit. Keeps them nice and snug. I used 6-inch height as I put fishing rods in the back. The holes (4-inch holes saw) are for weight reduction and additional tie-down/pass-throughs. The front and rear are identical. See pict of the final result. I rattle-canned them with Rustoleum truck bed spray and added hardware.

 

AFE

aFe POWER Front Tow Hook Red | aFe POWER

 

I really like those, might have to build a set myself!

 

Plugged in the Pedal Commander. Works very well the TTV6 in my opinion. Obviously, it does not make more power but it is nice to have the gas pedal function exactly the way I want it to.

 

Nytop makes some really good ones also

 

Took about two hours total other than waiting for the paint to dry.

 

Simple mods. Only owned a week. Army green tundra. Could not take the stuff rattling around in center console

 

looks fantastic! Gonna copy the divider idea (except I only need 1…… 5.5 bed).

why did you pick full Bedrug as opposed to bedrug liner only?

trying to visualize why a 2 x 6 works better for fishing rods?

 

I wanted the sides padded and also if you have just the bottom/bed then it creates an "edge" between the bedrug and the bare side walls that collects stuff and is harder to clean. Also, later, I may put a cap on for camping and I liked it better for that. I have a Taco with the classic and a Cap that is great for camping.

With the 6 in, the rods lay across both dividers and the reels have room to hang down on the first divider.

 

Added some window vents for the summer.

 

From where sorry did you obtain the vents?

 

Amazon, they are made of metal, very well built but If I had the option I would definitely have wanted a plastic one. I plan to add a small gasket where the vent sits on the window just to prevent scratches from multiple installs.

Window Ventilation Vents Compatible with Tundra/Sequoia 2022 2023 Automotive Rear Doors and Windows Vent Screens, Safety Windows Vent Blinds Accessories https://a.co/d/edrF5mb

 

Did a few things this weekend. Added a Snail Armor tailgate panel, the taillight switch to my SR5, Charvonia Designs Bed Tie downs, Tufskinz center console pads, TRD Pro Shift knob, TRD Pro dash piece, Got in my order from Diode Dyanamics, installed cup grips and installed the Shifter matte black piece.

 

Love that TRD Pro dash piece. Where did you get that? Was it hard to install?

 

Picked up a family toy.

 

Just grabbed it from the dealership. Took about 5 min. Super easy. The one screw from my SR5 piece was stubborn and very tight but it doesn't do a whole lot anyway.

 

Also if you want the two other small trim pieces to match on each side of the gauge cluster (Driver area, the part numbers are 55475-0C130-B0 and 55474-0C130-B0).

 

Nice trailer congratulations