What have you done to your 1st gen Tundra today?

The chromatic photo cut off line is a bit blue/ purplish, but if you can get past that they are a world of difference. I'd reckomend them. They're new so I can't atest to longevity yet. But well get there

 

Nice. Didn't see in your writeup but might have missed what LEDs you used in the mod'd housings?

 

I finally leveled my lights 4 years later after lifting the truck. I am no longer blinding ppl.

I got my driver seat tear fixed and cushioned, it's taking some getting used to, sitting much higher till I break it in. 100$ well spent, my buddy is doing his sequoia seat today


Added an LED strip to the camper shell for tailgate lighting, it doubles as inside shell lighting while the shell is closed for camping, I had to hot glue it on so it would stick, the 3m tape wasn't enough. Working on cleaning up the wiring, currently running off a 12v Milwaukee battery, i will be connecting it to the main battery this weekend.

 

I like that idea

 

Oh man, you have no idea.

 

Whatcha got there, a coastal DIY bumper?

 

I was curious what he was gonna put together too!

 

https://www.instagram.com/reel/C3IuV_hxJhJ/?igsh=MTZjYW5xeGs3cGc1YQ==

 

COLight Mini Projectors
CO LIGHT Anti-glare 9003/H4 LED... https://www.amazon.com/dp/B0CN72DSBT?ref=ppx_pop_mob_ap_share

 

That the colite LEDs?

 

One more time for the people in the back!!!

 

Yes i posted the linknto the exact ones I have. LED Mini Projectors

 

to the colights??

 

Imma fight all of y'all.

 

Yep, going to build a hybrid style bumper so I only ordered the center section.

some progress today, nothing has been fully welded yet

 

Damn some prerunner tubes coming outta that thing would look wicked.

 

I 2nd this

 

This is for that subbie meme isnt it

 

SMFH, dont you have a head gasket to go inspect

 

nah mines good

 

I hope so !

 

I can fix that...... Let me see your boost controller lol. You'll be faster for about 2 minutes

 

I got under it today and the driver side sway link was super loose and rattling! I ordered the thin wrench MetalPete recommended to get at the Maxx extended links and tighten down

This hit my soul.

 

I miss my MK6. K04 + water meth was a good time haha

 

Busy day today...

Oil and filter
Installed PIAA wipers since I've only used Rain-X for as long as I can remember on all my cars and they really just seem to work terribly on the Tundra.
Lubed all 8 zerks on the driveshaft
Lubed the SPC UCAs
(Finally) installed the Trail Gear LSPV brake bias extension ~3 years after lift


Repurposed the rear diff breather extension I had left over from my Frontier. Perfect fit. If I recall correctly, the union was a Toyota part when I installed it on the Frontier so makes sense. The Club Frontier guys recommended using an in-line fuel filter to prevent any dust/debris from being sucked back into the line. The i/d of the tube was too small to fit the OEM breather on this one, so I think it'll work fine this way.








Ran out of time, so tomorrow I'll finish up with the power steering fluid, and tire rotation and any other odds and ends I can think of.

 

I know everyone has their own opinion, but I’ve been very pleased with Bosch Icon for the last 8 years (if you end up not liking the PIAAs)

 

Thanks, I'll keep them in mind if these don't work out. I was just driving through snow yesterday and the Rain X were leaving a 4" streak right in my line of sight driving down the highway. Literally weren't touching the windshield. Trashed.