OEM FOG LIGHT REMOVAL

It’s seems the blue tab is holding it but how do you get it out

 

See if this helps.....

https://www.tundras.com/threads/2018-led-fog-light-installation-instructions-w-pics.18346/

 

I’ve always just pried the housing out the front. Use a trim removal tool and it’s pretty easy.

 

Thanks all

I greatly appreciate it.. i had to goto dinner with the wife so I will have to get back to it tomorrow. I had a metal plate come out and I will have to find out where it went
I am in no rush ( will I have three days ) but I need to order some new fog lights by tomorrow

Diode dynamics pro are on the top of the list rigid industries D series and one other but i am indecisive at the moment and I am looking at the pros and cons of them all

 

had time to read through the link,,
clear and concise.. thanks.. even the bracket was covered!!

 

If you go DD ss pros you’ll need the oem led circle bezels

 

Message sent

 

Thanks so much guys

got a different problem

where does this metal bar go? It does not line up with the two holes on the side

 

Going to get them taken care of shortly
Thanks
I decided to go DD but the ones above the pro line

 

FYI

I looked on the parts website for a diagram and couldn’t find it. Went to a local dealership and well here I am

 

That goes on the bumper for the front mud flaps

 

On the bottom on the bumper where you take off the 10mm and there’s 2 12 mms

 

It’ll line up on the bottom of that slapsh guard you have off

 

Good Evening all

Thanks.. I was wasnt even thinking about that thing. I am going to just put it on just to cover everything up until the lights arrive.

 

$17 For Toyota Tundra 2014-2021 Fog Light Bezel Driver Side | Front | Made of Plastic | Replacement For TO1038175 | 521280C070, 615343560670

https://www.amazon.com/dp/B0B3S9T3J1

 

521270c060

 

I just searched 2018 tundra bezel

 

Be sure to zip tie the DD’s down when you install them. They’re going to want to bounce around in there and they’re even more noticeable than the factory fog lights. Poor design by Toyota on the housing.

 

I cant just be me. Lord knows I tried today.. I got the DD square bezel in and changed them out.
Went to put the DD SS3 Pros in and guess what.. My brackets are not like all the others that I have seen on the internet

 

it is not possible to mount the lights on to this bracket

 

Yes
The TRD Pro square housing is set up differently than the round ones that everyone makes brackets for - the tabs and interface are way different

you will either need to order round ones or you’ll need to make something that will mount to the stamped metal bumper sub-frame and hold the lights in position

 

Thanks.. i was going for the square face look which is why I ordered the squared bezels. I thought I had did all the reading and research that I need to do..
kinda sucks being having to go back to the round. I will resist and find some alternative. Thanks for reaffirming my suspenion.. Seem like DD would recognize that not everyone wants the round bezel especially that price point. right now i have nothing in place

 

I just swapped in some BD fits this weekend and switched to the round inserts (they only offer the fog trim with a round bezel). So the comparison of mounting points is fresh in my mind.

It would be easy enough to fabricate something that attaches to the stamped metal frame.

 

DIY RIGID TRD PRO Fog Lights Brackets | Page 7 | Toyota Tundra Forum (tundras.com)

imma go this route

 

Thank You.. I really appreciate it.. Especially being a new comer to this community, your help, guidance, ideas and support is greatly appreciated

 

Gotta re-use the brackets from the rigid fogs

 

Went a different route altogether
They will be installed on Monday but my local shop whose done plenty of work for me

Can’t wait to see it all done using the oem SQUARE housing. These guys are smart

 

Ooo please post it when you’re done

 

Installed

 

Fully functional with back lighting