1st Gen. Lunch Table - General Discussion

https://youtube.com/shorts/2xjIYUfXkgQ?si=zq1ug83ByXgMi7Xa

Stumbled on this...

 

https://www.youtube.com/watch?v=GnxgE1znL9w&ab_channel=DanK.

 

So who rebuilds these POS things?

 

You taught an assdog new tricks.

This left me with a sinking feeling.

 

I bet 4LoFab does

 

https://youtu.be/P9bB5V6gTn4?si=80QnTnqSpsxBNFPD

You do now

 

I did, much rather have them on the truck than POSs from Napa or RA

 

Everybody hating on Napa but I been abusing mine for five years with no issues. Plus they have a lifetime warranty.

 

they're spares, now. And not just for me, if someone breaks one & i'm nearby, i'd trade one for a leg, or a soul, or a first born child.

So do the trackmotives.

 

Nice

 

I’ll be getting a reman Denso alternator from NAPA down the road. Other than hearing about suspension parts, I’ve had good luck with most of their other parts

 

I've rebooted my own, but I've never refreshed the bearings and I believe there's some sort of trick to the outer joints, or you have to cut the snaprings and put new ones in. I'd really like to learn how, now that remans are discontinued.



Also on the inner joint, I think you'd have to separate this part from the tulip to get the cage out.



https://www.youtube.com/watch?v=3-R11jtnyV8

 

Hard sigh, hard hard sigh

 

Make sure they still have them. I bought one of the last reman alternators last year. They are different from 02-06 though. Maybe you'll still have luck.

 

You’re going to need a bigger & deeper sink if you expect to wash car parts like @bmf4069.

Good job, BTW.

 

@Tundra2 i'm jelly. Eaiting on my enameled sink to break to go stainless.

sand & polish it.

 

Hopefully @Tundra2 didn't sink too much time into it, real drain on resources. Seems like a wash, the old sink looks almost identical to the new one.

 

Damn you punny.

 

Couple of my buddies up here in DFW used an axle or differential shop locally and it's cheaper than these "toyota shops". Also reminds me I've got an OEM reman off my 2.5 gen I need to get my core charge from since I don't have the truck anymore.

 

Thank you, this is the deeper sink. We didn't like the short one that was new to the house. Plus the faucet left a lot to be desired.

It's like 8" deep versus the 6" that was in there
https://www.amazon.com/dp/B074WHVFDS?ref=ppx_pop_mob_ap_share

We have a

$66 WEWE Single Handle High Arc Brushed Nickel Pull Out Kitchen Faucet,Single Level Stainless Steel Kitchen Sink Faucets with Pull Down Sprayer

WEEWEE faucet

And new strainer baskets!

$20 3-1/2" Sink Drain Assembly Kit, Removable Deep Sink Strainer Basket with Sink Stopper/Sealing Lid for Home, Kitchen, Stainless Steel

https://www.amazon.com/dp/B012Q5RTSW?ref=ppx_pop_mob_ap_share

 

Side note: fuuuuuuuucccckkkk those sink anchors clips. Holy fuck

 

Penis screw.

 

So you got it extra deep with a weewee, single handle, is what you're saying? That's awesome bro.

(I hope you know I'm going to keep ribbing you on this, but I'm still no less proud of you)

 

@shifty` Is it the JBL club series you like?

 

Old sink: crusty, and very "single man life" (previous owner)

New sink: shiny, nice, and cleaaaan

These two are sideways or upside down

 

Get in there nice and deep like

 

I like those deep baskets, never seen those before.

 

I'm a fan of the Club series. Good all-around sound, solid midbass reproduction. You won't be winning any SPL competitions with it, but the mids they offer up in the set typically sound good with E-string on guitar, D & G string on bass for example. If you have an amp and sub, I'd probably tinker with crossing over to cut everything below 120hz/130hz/140hz on the mids.