3rd gen 1” Cornfed front spacer

I’ve been digging through the lift kit and leveling kit threads and haven’t been able to find anyone running the Cornfed 1” front spacer. I was curious if anyone had pictures of their truck with them installed and how they are liking them.

Thanks,
Mason

 

I put the Cornfed 1" spacer on mine. The pic of the truck without tools scattered everywhere is the after as is the shot of just the front wheel. The other pic is the before shot, not a huge difference but it's a legit 1" taller in the front. I like the more level look and it's also more practical for me since I pull a trailer or have dirt bikes, wood, etc in the back of the truck. I like it, no issues with it at all but you will have to get a front end alignment after installing it.

 

Thanks coasty! That looks great. I’m in the same boat and a higher leveling kit wouldn’t work for doing a lot of hauling. I really appreciate it.

 

Thinking of doing this too. Looks good

 

Thinking of going with 275/65/20 or 295/60/20 all terrain.

 

I just finished up the front spacer and put 275/60/20 recon grapplers on. Couldn’t be happier. I’ll get pics as soon as the weather cooperates.

 

I had the 1” rear installed today to level out from the RC 1.75 in the front. Stance looks perfect now IMO.

 

Called cornfed and confirmed the 1/2” spacer (for 1” lift) doesn’t require longer studs. Ordered, will go nicely with the 295/70r18 tires I think

 

Just got mine delivered today! Will install next week with new 295/65/20 Toyo AT3!'s and post some pics.

I have the 24 Platinum with AVS, plan on adjusting the lever to max as well to see how the stance will look. Will update soon!

 

Can we get some measurements people? Are you guys sitting level with the 1 inch cornfed front end lift?

 

the rear is still higher than the front. I can measure tomorrow but I know my before and after measurement was exactly 1” higher. If you have the same measurements front and rear it’ll look nose high

 

What would be the appropriate way to measure for a level "looking" truck?

 

Mine sit .75” higher in back and looks level. True level makes it look nose high.

 

Don’t know, but your truck is the same as mine and the 1” front looks good.

 

Do the non trd off roads have more rake? I know the sports sit lower on the front. In my case 2” up front would be nose high for sure.

 

I have a non trd or and have been trying to figure this out before I buy a kit(but I’m leaning towards 1” cornfed up front).

Anyone with this setup running 295/70/18 and notice it gave them any extra space between the tire and uca? I’m running wildpeaks in this size and while no rubbing, it’s super close. Like 1/4”, wouldn’t mind a little more space.

 

No idea, have that exact setup and no rubbing on uca but didn’t really look before vs after levelling kit.

 

Got tires installed, they couldn't do alignment so thats setup for next week.

Toyo AT3 295/65/20 - No rub, stock mud flaps

24 platinum with avs and air bags
1" cornfed front lift only
Rear air bag lever is at stock height


here are the results!

from center cap to bottom of fender
22 1/4 inches front
22 1/2 inches rear

 

Looks excellent! I just purchased 1' cornfed front lift from a member.

I probably won't install until I burn through the stock tires.

 

Can anyone tell me if ride quality changed any after installing the 1" cornfed?

 

Nothing noticeable here. It’s not a pre load spacer.

 

Likewise, feels similar or a little better than stock..

I have my avs lever maxed out in the back as well.

 

Picking up my limited OR tomorrow. The 295/65/20 Toyo AT3 should fit the stock setup with no rub correct??

 

I'm not totally sure, I put the 295/65/20 after I did my 1in cornfed lift in the front, rear suspension is stock, I just maxed out the avs lever. You might be cutting it close.. I'm not sure, but u might need to trim some inner liners..

 

Ahh gotcha, I’ll have to do some measurements, worst comes to worst I’ll just order the 285/65 size and I’ll be good

 

Do you have a pic of this setup? Would love to check it out.

 

Just ordered the 1" kit today for my Limited TRD Off-Road

 

I haven't installed the 1" spacers I bought second hand.

I saw Cornfed now has collars, has anyone installed them and if so how is the ride quality?

 

I have their 2/1 kit. Rides great

 

Does the collar raise the front 2"?