What have you done to your 2.5 gen Tundra today?

A PC and tow haul are two separate things. They operate differently.

 

Looks so good. Fwiw I was able to move my whole front inner fender forward a great bit and just re fasten it from the bottom. Leaving the liner intact

 

Agreed. One is shift points and one is throttle response from the way I understand it. I don’t have one, but my buddy has the PC were playing around with it and it was pretty lively off the line. Seemed to be a difference using both (maybe not-could just benperception ). Anyway the lag was gone and acceleration seemed to be pretty damn quick. I’d say close to any 3.5 ecoboost for a short duration with a high rpm holding those points longer.

 

Same thing happens when you press the gas farther initially. That's what the PC does.

 

first you go and send me down a rabbit hole on buying cheaper lights and trying my first retro fit... then you send me down another google session on what are chase lights, followed by what tail lights are different than yours but I could try the same with.... And now you go and post a video and some pics.... back to google again.....

Side note, my stock tail light is taking on moisture... I think that means new tails right?

 

Geno is also incredible at answering pm's with info. I've definitely asked him lots of questions about his mods.

 

Good to know and thank you. I have been holding off on one of those switch ports (not using a brand name on purpose) but feel this would help justify and be useful on the game roads and what not.

 

Thanks for the compliments!!
For your stock taillight, I would check the rubber grommets where the bulbs are seated. One may be cracked or missing.
For the switch pod, you may not need one! I don’t.

 

I like that a lot! You did it clean!

I will check them when I go to reinstall my dash cam. Thank you for the advise!

I want the switch port for ease of use, but I also know I am not going to install everything at the same time, plus you found a great way to use that useless spot. I finally started putting my park access cards there just to do something with it.

 

Thanks! Right now I’m not using all the switches (buttons). They’re wired to the engine bay, ready for relays and whatever is next.

 

Another idea I may have to pursue instead. And prewiring them is way better than running each time. During our gap in time here I was looking at making my own distro block setup LOL.

This forum is the worst sometimes.

 

Agreed! But the more ideas, the better. Makes the job much easier with all the options on the table.

 

BMC 2.0

 

Got new tires yesterday, rubbed a little on the front so spent a few hours with a heat gun and plastic welder and no more rubbing

 

Looks really good. What did you use for wire? Thinking that since those are no load switches that you could probably get away with cat6 which is 4 pair of 24ga. I think cat5 is 28ga.

 

Added 1.25 wheel spacers and yellow film for the fogs.

 

I decided to pick a fight with my liberal water nazi neighbors today and actually wash with water

 

Well, that would have been a good idea
I used individual 22ga., but consolidated the ground and power, of course.

 

Installed the Alpine ILX-F511 this afternoon. Also opted for the integrated front and rear dash cams that can be controlled through the head unit. Don't mind the sticker residue on the screen...I haven't peeled off the factory screen protector film yet.

 

@STravis SOB Fabrication

 

I (actually my girlfriend) installed this leather steering wheel cover over my plastic wheel. It only took her 5 hours

 

Did you marry her yet? That 5 hours is more than my wife (almost 20 yrs) has ever spent helping on my truck

 

Tanning booth?

 

Night runs on the beach at speed are wild.

 

She's a keeper!

 

no, I’ve done the tow/haul just to see what it will do. I haven’t gotten the PC delivered yet. Install should be in a couple of days. Should have clarified!

 

Nice....wrap color matches the truck very good. Shade of color matches well. Awesome job.

 

How’s the clearance from the tire to the UCA with the factory BBS rims and those tires? I’m thinking about upgraded UCA’s but there’s not much room to spare with the factory BBS offset.

 

Not on my 2021. There is no way I can get that sort of throttle response by mashing the gas. Same for my buddies 2015.

 

That’s exactly what it is doing. It’s just opening the throttle sooner. All it’s doing is say at 25% throttle input, it’s opening the throttle body 35%.