The Great HU Install of 2023

Which dash kit did you get?

 

And I’m here for it.

 

Anyone with a Kenwood have a solution for the xm tuner hook up? Might just leave it be since I don’t use xm anyway.

 

Is it the plastic brackets that are the issue?

 

I bought a sheet of ABS and cut a filler plate for mine (threw away the pocket…). I can send you a chunk if you want to go with the Dasaita kit

 

100% this haha. I’ve redone my shit so many times because something that should work doesn’t work the way it should or the way I want it to. I’ve bitched to @BiggHertz a lot over the last week…

 

I bought

$30 Maestro Acc-SAT-TO2 Sat Radio and GPS Antenna adaptors for TO2 Vehicles

this

 

whoa whoa whoa

 

Indeed!

 

So does this new head unit run the speakers or is it the same amp under the seat? I have a non jbl. Seams way louder to me, but maybe I’m dreaming.

Only had to take the thing out 3 or 4 times before I got it. A little tip I found on the Kenwood is that you have to slide the unit up to get the AC control back in if you want it to sit as low as it can. Not a big deal to move only 4 screws. Or you can just have it set high with one screw holding it in the side until you are ready to put it back together.

 

Ah, I lied. I went to put the mic in today and, nope, not happy with the hassle. It was actually easier to run up the A pillar, oddly.

 

Ok, so I ordered the USB/HDMI port to install in the bottom tray under the radio (by the USB/12V plugs) which will arrive tomorrow.

I've been looking at the instructions for the Alpine DVR-320R and I'm not sure I follow how to connect it directly to the ILX-F511. I'm not using the Car Charger Cable, but will be doing the hardwire method instead. I understand plugging in the cameras and the Yellow/Red/Black connections but am lost on the "F CAM" connection as well as the "REMOCON IN" and "REMOCON OUT" and how these connect at the back of the Alpine. Am I going to need the "sold separately" cable noted in the diagram? If so, wonder why Alpine does not include that to integrate with the head unit.

The Alpine manual however shows that the "Drive Recorder In" and LIN are used for the Dashcam connections. Do I not need to use the "F CAM and the REMOCON In/Out from the dash cam wiring and will be using the 2 LIN Cables instead and plug the yellow rca from the F CAM cord into the Drive Recorder In on the Alpine harness and leave the red/white rca's unattached?

@BiggHertz any ideas on this one?

 

Anyone remember if the black connector is XM and the white is GPS, or if I've got that backwards on my 2015 non-JBL?

 

IIRC, white connector is GPS and black connector is SAT. Confirm by following the white connector to the GPS antenna that is about 8-10 inches to the left of the center speaker.

 

I don’t have any explicit experience with this integration, but in previous generations, some of the Alpine h/u’s previously utilized a combination 1/8” jack that included stereo audio (red + white) and video (yellow), which they simply carried over in their documentation or failed to update it entirely.

While I’m not certain, I do feel that the signal delivery from the dash-cam DVR to your h/u can be accomplished by utilizing the composite video (yellow RCA) and the LIN connector.

 

Thanks for the response. I'll give that a try when I get ready to install (Using the Yellow RCA and the 2 LIN Connectors).

 

Unless you’re daisy chaining multiple LIN capable devices. You should only need just the one.

 

Crutchfield just responded to my message as well. They stated to follow the head unit manual instead of the Dash Cam instructions. I was told to utilize the yellow RCA and Lin Connectors and I should be good to go aside from also connecting the battery, acc, and ground connections of course. Hopefully this helps others out too. Not sure if anyone else ordered the dash cam or just me.

 

Just letting everyone know I've been buried this week and am now 4 pages behind on this thread. I will hopefully get through it later tonight and get updates and new links added.

 

Slacker…

 

So lazy. Classic Casey.

 

I had issues with one of the four screws as well and it began to strip, but luckily it was still useable. My advice is to adjust the height and put those screws back in, but not completely tightened down because you may need to take them out again for more adjustments. Also found it amusing that when you drop to the lowest height and try to reattach the screen you can't because of the angle. That's why I say not to fully tighten those screws in case more decide to give you trouble. I had to adjust the height, then tilt the angle before I could drop the height some more.