WHAT HAVE YOU DONE TO YOUR 3RD GEN TUNDRA TODAY?

I just bought the Yakima Baseline Towers and installed on my 2022 as I already had round bars (used adapters) and accessories. They are very secure. I hauled a 16' canoe on it down very rough roads, dry creek beds and at 80+ on the interstate without issue.

Finding a place to tie a backup rope to the front of the truck was fun without tow hooks. At least the giant grill surround prevented the rope from rubbing the paint off the hood!

Was a bit concerned that the rear bar is so close to the front one when installed as recommended, but it looks like the Thule is the same way. There is a whole lot of open roof behind the rear bar.

 

And here I was going to suggest a piece of plywood and a come along run to a back tie down.
Not so deluxe as that lift posted.

 

not with the @GG.Offroad camera relocation kit. Bed camera and PVM camera still work great! The 360 camera has nothing to do with the 3rd brake light cameras

 

Got my 295/70/18 AT3Ws installed. Pretty happy with how they look/ride.

 

What psi are you running em @?

 

I think they put them at 37/38 psi. I drove home and parked it. I will check it out tomorrow. I have only had the truck for a week and 400 miles. Not sure what is good/bad yet. The dealer did “correct” my alignment while there. It looks like there is still a good bit of positive camber still. I think I am going to do a Firestone lifetime alignment and be done with it.

 

Don't do that, you need a shop that knows what they're doing.
Your + camber is insane. Get it to 0.0 with high caster or even negative.
Check out my post on the TRD Pro alignment here:
https://www.tundras.com/threads/trd-pro-alignment.126131/#post-3223239

 

Finally got my westcott sliders...now to make time to install them.

 

You’re supposed to leave those bastards

 

What steps did you take to make removing the decals easy?

 

This is a great way to do this. All the badges on are this way right, so this can be used to take any of them off?

 

You not a fan?

 

S&B intake and aFe Charge Pipes installed yesterday.. wasn't too bad and video from S&B helped. Needed some lube for the breather hoses onto the charge pipes but not too bad all around.

 

Sweet! Mine is delivered today!

 

What does the butt dyno say?! How’s she pull?
I feel like your missing a JB4!

 

Initial throttle response seemed quicker, but that could just be from computer reset after unhooking battery.

As for the JB4 .. look closely .. it's not missing!

 

Door moldings, yes. I think the hood badges have holes (I dont have these on my truck)

 

Nice. I'm waiting for the afe scorcher for the hybrid. They told me like a month out.

 

You're selling kits for me left and right! Appreciate you dude!

 

prototyping has paid for itself at this point!

 

Added some Rago Fabrication bed stiffeners today! Did some test fitting for them to check clearance with the DECKED system- worked perfectly!

 

Looks good. I’m torn on getting bed stiffeners.

 

I was as well but glad I did, my passenger side was already off when I installed them

 

What do you mean by off, as in not square?

 

Installed the AirLift 5000 bags. Didn't have horrible sag before. But the bags eliminated anything there was. Boat is just over 5K lbs (Boat, motor, trailer, fuel, etc).

 

The worst way to bag one. How’s the front end?

 

I did all the Carista mods; turned off the sound, belt digs, turned on the windows going down….

 

Awesome. Send it over to me to do too lol.