GEN 3 (2022+) Wheels and Tires Photo thread

Decisions, decisions. Keep truck or wife? Gotta have my truck sooooo, keep wife so I can afford to keep truck, yes.

 

I’ll be very interested to see if you rub on sway bar

 

I run 305/70/18 basically a 35 with .5 more height and I don’t hit the sway bar
With 18x9 with +20 offset

 

3/1.25 ReadyLift
I should mention also that the 305 is taller then the 35 tire it’s also not as wide. I’m around 12.2 and the 35 is 12.5
Just so no one gets confused.
The reason I went 305 because I wanted a true 35 tall tire and it’s also around 3 lbs lighter per tire.
305 load range D Diameter 34.8
35/12.5 load range F Diameter 34.5
Nitto Recon Grappler

 

Interesting I didn’t know that
Def send pics when done.

 

2022 TRD Off-Road
-2” Spacer Leveling Kit
-35x12.5x18 Nitto Ridge Grappler
No rubbing or trimming done. Just missing the upper control arm by about 1/4”. More than pleased with the stance of this setup. Stock wheels are +60mm offset so there is little to no poke.

 

Is that just 2” in the front no lift in the back?

 

I am surprised that those tires fit on those rims. At 7.5” wide they are quite narrow.

I will have to get mine painted black and contemplate using them as a second set!

 

Yes! Nothing in the rear and it sits complete level. Got a 2” space off Amazon for $45 watched one YouTube video and did it myself pretty easily.

 

Yea I was slightly concerned, but with the narrow rim there is a lot of bulge with the tire which I feel looks great!

 

I’m surprised a shop would install the tires on your stock rims
More power to ya
The narrowest rim size is an 8.5 for
35/12.5 and the factory rim is 8.0 inch
I bet she’s bulging lol

 

you have a lift or leveling kit? Or that stock ride height just with adding the wheels and tires

 

I took off the sway bar but wasn’t rubbing it before I removed it.

 

could get her helicopter ladder for the passenger side

 

Method 701 with 285/65 R18 falken wildpeak at3w. Not planning to lift or mod, just a work/tow vehicle.

 

-10 offset

 

That is sick what size tires do you have?

 

I'm looking to put 37s on too and my wife is 5'0". I'm sure I'll never hear the end of it lmao

 

How are the driving characteristics with the sway bar off? Any noticeable difference?

 

35” BFG KM3s

 

Holy Crap, it's washed up and looking pretty!!!!

 

Good job guys ,just waiting to get my Pro. I’ll reach out when it’s time for 37s

 

haha good one. did you use AI to make this?

 

Im picking up a '23 Sr5 on Friday, this will be my 6th tundra, I got a deal on some 35x11.5x17, is the centerbore a huge deal? Having trouble finding 17's with 110.5 bore, any suggestions?

 

Hi there, i bought a 35x11.50, but honestly i would prefer by 12.5, mine do not rubber on any part.

 

To the guys with 4 and 6 inch lifts I’m assuming garages are no way fitting but what about restaurant Drive throughs or parking garages?

 

Finally, I haven’t kept reading from this post, but been waiting to see 37s on this thread. I’m planning to upgrade sometime this year, after I get my front end swapped again. Anything special you have to do for no rub? What’s size and offset of the wheel?

 

Not a single size in that wheel comes hub centric to this truck. Just thought I’d throw that out there. As long as they used ET lugs properly, you don’t NEED hub centric spacers. I put some on for peace of mind, doesn’t make a difference to me. But I thought I’d throw that out there for the BS factor. Trust no one.

 

the 3 hubs that came with my fuel flame 6 were all the wrong size. my tire dealer had to have them send the correct size that came in a week later.

 

WrapCo watch the video a few posts up
Will Answer all your questions