Door sill protector

Any recommendations for a good inexpensive door sill protector for a 23 Tundra crewmax.

I know Tufskinz makes one, but it’s $100 total for front and back.

 

Get the black stick on ones for the 21 and below. I do not know why they would not work?? All four for 34.80


https://www.sparksparts.com/oem-parts/toyota-door-sill-protectors-crewmax-pt74734144?c=Zz1pbnRlcmlvciZzPXNpbGwtcGxhdGUmbD0xJm49U2VhcmNoIFJlc3VsdHMmYT10b3lvdGEmbz10dW5kcmEmeT0yMDIxJnQ9c3I1JmU9NS03bC12OC1nYXM=

 

The 22-23s door sills are more “vertical” if that makes any senses. I just can’t talk myself into paying 100 bucks for them tufskinz ones.

 

Got info with your pic?

 

That pic was just take from tufskinz website for 3rd gen tundra.

 

Oh I see, thank you, I didn't realise that.

 

I thought you meant the plate not the front of the door edges,, or what ever that is called. Still you out to get some XYZ non skid in a sheet and cut to fit like the picture and press it on.


Or even some type of rubber sheet

https://www.homedepot.com/b/Buildin...-Sheets/Non-Slip-Backing/N-5yc1vZcj87Z1z0s9zz

 

Thats actually a pretty good idea with the non-skid tape and just cut to size.

 

Tape it off wipe it all off and spray can bed liner on it? There are lots of options. Good luck

 

Well if your going to tape or spray bedliner on it I would do anything until got scratched up bad the sand it and do something

 

I usually just vinyl wrap the same body color. Pretty simple

 

I second this

 

Added this anti-slip grip tape to mine the other day...

 

looks great. Where did you get the tape? Amazon?

 

I had some extra in my shop, but im sure pretty much any kind of grip tape would work

 

Is that more than one piece you used or a solid piece? Also, do you recall the specific tape you used? Thanks for the help! Looks awesome!

 

Thank you! I believe I used 3 pieces of tape. unfortunately I don't know the brand of tape I used (it was some extra I had laying around the shop). It is a lot easier to work with if heated up with a heat gun or hair dryer. But is defiantly do-able without. (I did not think to use one until after the driver side was installed)

 

Tough skinz Carrie’s those protectors. About 150 for all four doors.

 

I like how you went on the furthest edge of the rocker. The kits don't touch that area and that's the part that I seem to kick most often.

 

link?

 

https://www.tufskinz.com/collection.../products/tun068-rear-door-sill-toyota-tundra

 

I am thinking of using 3M clear protective film. You can get it in 4 inch widths and various lengths. It should'nt hold any dirt like the anti skid tape and be more invisible. Sometimes less is more.

 

Did you do this? I want to do something like this and wondered how it worked for you?

 

Yes I did do this and it worked great and still holding strong over all these months. See link below, post #4589. I figure for $30 and a bit of my time I could redo this a number of times for the same cost as ones from Tufskinz. The 3M stuff is also easy to wipe clean, much easier than a grip tape but that works good too.

https://www.tundras.com/threads/what-have-you-done-to-your-3rd-gen-tundra-today.104778/page-153