3rd Gen Accessory Thread

Tow Hooks Installed

Just installed the aFe Powersports 2022 Tundra Front Tow Hooks.

 

First mods on new SR5 TRD include LED tail light strip above bumper, combo bak mx4 & truxedo Elevate FS Rack & T-slot rails. Combo looses the stock bed rails due to not being able to use the MX4 hardware. I made some parts to drop the MX4 hardware to keep the bed rails. Also drilled holes in Elevate FS rack to enable a height in line with the top of the cab so the truck would still clear my garage door. All good, happy with the functionality.

 

front of the truck looks so good! I’m even divided on the stache with the lunar rock

 

Thanks for the pics.
Are we all in [sad] agreement that unless you're being pulled by a turtle, the hooks are but a red ornament?
(unless you're looking for a quick and easy way to disassemble you're entire front end)

-99

 

Mud flaps, any suggestions out there who has installed?

 

It is unfortunate isn't it? I expect many will be looking for a replacement bumper design that will work with tow hooks and probably a winch too. I don't really need a winch, but functional tow hooks would probably be a good thing.

 

At this point it’s a better than nothing for me. But I do recall my 2000 Tundra didn’t have any either

 

I'll use them for pulling Honda Civics out of the snow banks here in Canada.

 

Let me know how you like yours, my 23’ trd limited max is being built on the 22nd.
What is your take so far?

 

Getting our 1794 TRD in a few weeks and wondering what the consensus is on running boards that do not impact ground clearance (in the middle of side of truck) much or at all? Thanks.

 

Do you need sliders or running boards?

 

I’ve only had for a couple days and put roughly 50miles but love it!! Huge difference between my 2015 SR5. Fit and finish it much improved.
I’ve added the following:
-Rough Country level
-Open Country III 285/65/20
- Borla 1” spacer
- Retrax PRO cover
on order, TRD Black chrome exhaust tip, TRD air filter, bed step, and bed mat. I also ordered Husky liners.
Going on a family run tomorrow, local diner breakfast and to check out the ski mountain for upcoming season, should be a fun drive!

 

Just got a 2023 SR5 crewmax TRD Sport and I'm thinking my first order of business is installing running boards. Any recommendations? Any good websites besides Amazon?

 

Keep me updated. I just checked my employee cost on the Trd lift at work.

 

Any feedback on Tufskinz mud flaps out there?

 

Don’t forget that the 2022 Tundra TT V6 has two air intakes/filters. You’ll need two TRD filters. Had the TRD CAI on my 2016 Tacoma TRD Sport and loved it, so I put them on my 2022 TRD OR Limited. Not sure if a CAT Back would make any difference.

 

Anyone know if Go Rhino has Black Friday sales? Looking to get some running boards eventually but not in any rush

 

Probably, but they also give you a 25% code when you sign up with email got the sliders and brackets for $733

 

Good call! Thanks for the heads up.

 

Yup. I just ordered the powered running boards from them and got the 25% discount too. They say 12/16 for shipping.

 

Added lights in the bed today, they provide a lot of light and have a push button switch, wired for direct power. Ran power from batter back to passenger side tail light to tie in, the kit has an in-line fuse. Grounded them with and existing chassis bolt under the bed. Not sure the adhesive will hold up but will fix if not. Soldiered all connections and lug for hot wire on battery post.
Videos would have you drill all sorts of holes in the back but I did it with only drilling one small hole for the pushbutton, cut the wire, fed it thru, then soldiered back together. Use double faced adhesive on the button (not included), pretty hidden so it won't get pushed by accident.
YouTube install video:. https://m.youtube.com/watch?v=zdbbVnDnG6Q

Bought the lights from Amazon, recommended on several sites so I gave it a shot, so far so good.

Lights:

$33 Nilight 3PCS 60" Bed Light Strip 270 LED with On/Off Switch Blade Fuse Splitter Extension Cable for Cargo Pickup Truck SUV RV Boat,2 Years Warranty

https://www.amazon.com/dp/B07ZLWJZLT?ref=ppx_yo2ov_dt_b_product_details
Conduit:

$17 ZhiYo 50FT 3/8” Wire Loom Split Tubing Auto Wire Conduit Flexible Cover | High Temperature Heat Resistant -40F to 257F | Plastic Cover for Electrical Wires & Cables

https://www.amazon.com/dp/B07PNBYWMP?ref=ppx_yo2ov_dt_b_product_details
Wire:

$12 GS Power 18 AWG (American Wire Gauge) CCA Primary Wire | 50 ft Red & Black | Also Available in 14 & 16 Ga

https://www.amazon.com/dp/B07D74RGVM?ref=ppx_yo2ov_dt_b_product_details. (low wattage so this gauge is fine)

 

What site did you buy this off of?

 

https://www.ajtdesign-llc.com/online-store/2022-c133992787

 

Which version is it flush or one with bar? Would you be willing to ship? Sent ya a message also. Thanks B

 

Any further update my friend? I’m just getting ants in my pants since mine is around the corner.

 

WHich LED Tail light strip? @CKOPIX

 

@brewjd - it came with a 4-pin trailer connector and the mate. I wired the mate into the harness so if it breaks, I can unplug it and plug in a new one. Also drilled small holes in plastic between bumper and tailgate and used black zip ties instead of drilling so it would not block the spare tire hole. Also didn't trust the adhesive.
49" LED

$55 49" LED Tailgate Light Bar for Trucks [Rigid Aluminium Frame] [Amber Sequential Turn Signal] [Tail & Reverse Light] [IP66 Waterproof] Rear Truck Tail Under Tailgate Brake Light Bar for Cars Trailer

https://www.amazon.com/dp/B07YNZ5XHX
Short video: https://photos.app.goo.gl/Zx99jq94smDMbr7x9

 

@CKOPIX Can you provide more detail/pics on the install of this light bar please? I don't see how it can be installed without blocking the spare tire access slot. Or is there a way to use the clips to mount without drilling holes? Maybe a 2-sided tape to mount the clips? Maybe that will provide easier access to the spare tire slot?

 

@brewjd - this is how I did it after evaluating the options, just sharing as one alternative, may not be right for you. I didn't see a way to use adhesive as the bar goes over the top of the license plate holder. I am happy with it as i didn't have to drill any metal parts. Also, you can pop out the existing wiring harness and get the LED cable through to tie into the cable harness without drilling. OR you can plug right into the trailer hitch on the bumper, too messy for me with cable and I pull a trailer. I used a multimeter to make sure I was splicing into the right lines in the harness, lost my notes on that but you can figure it out pretty easy. Please post some pictures if you hook one up. I will say drivers see me a mile away now, never have an issue merging or changing lanes.