What have you done to your 2.5 gen Tundra today?

If they are little sugar ants what I have found that works the best is to use the little white Raid ant traps and mix the solid bait with some Terro liquid bait (cut the top off, squirt a bunch in and mix with a toothpick). They seem to like the taste of the Terro but the Raid kills them better. Usually kill a colony in under 36 hours.

 

Rolled over 50K a couple of days ago. Sorry I’m late.

 

Probably will get way more use than the air compressor I just installed...

 

I’m trying to stay strong and keep my mods for the tundra reasonable. All unreasonable mods go into the tacoma.

 

Looks like it might be this:

$20 WirthCo 94367 Measuring Container, 5 Liter

Amazon.com: WirthCo 94367 Measuring Container, 5 Liter : Automotive

 

priorities lol

 

Nice.

 

Oh yeah!

switched over the longer one to the metal housing and then challenged daughter to put short one on the plastic housing

 

Below is the link to mine. I love it!

Pour in the exact amount needed in the container and just dump into engine. Quick double check of oil level gauge and keep moving.

Did end up making my own zip tie holder for nossle end as it would collect oil at end of hose as oil setting.

$20 WirthCo 94367 Measuring Container, 5 Liter

https://www.amazon.com/gp/aw/d/B071FVDWQB?ref=ppx_pop_mob_b_asin_title

 

Those are where they should have originally been installed by the manufacturer… Such a convenient location. I wish I had the cut on my platinum I would have relocated mine by now.

 

You can always get the non-platinum trim piece that goes there…

 

BD S2 Pro reverse lights in the bumper

 

As with many of my Platinum parts, I purchased the "cheaper" non-platinum version. This piece included.

 

Do you happen to know the part number?

 

You just need to find some good uses for it. Should make removing dog hair a breeze instead of vacuuming. Or removing all of the dust when you roll all the windows down

 

SCS Ray-10 and 37’s.

 

What did you use to drill your holes? Does it come with a layout? I don’t see any directions with mine

 

We printed directions from the site. It tells you were to line it up, and gives dimensions for a second confirmation (holes should be xx down from edge).

We used a paint pen to mark the holes, center punch to get the direct middle, new titanium step bit, wd40 for drill lube and a corded drill.

It went smoothly.

 

Yessir it was. No issues at all with it beyond the positioning of it in-dash. The screen size wasn’t my problem necessarily as much as the tilt/angle of the screen with it being set back in the dash (seemed to pull more glare reflecting from the black trim on the bottom). Was a little tough to see sometimes, but otherwise it was perfect!

 

@GELCW this is what I ordered from McGregory Toyota and fits perfect. I have not completed the switch move mod yet but on my list.
58805-0C090-C0 Console Trim Panel (Rear, Upper)

 

Gotcha. I was looking at the 4500 but it has issues with failing internal SD cards that stores the firmware and there has never been a firmware update from Pioneer. Some left bad reviews on the 4660 that you had. It's giving me a headache. It's either then 4660 or the 7600 floating 9 inch.

 

That’s a nice looking rig. Did you swap out your button head bolts on your fender flares. I bought black stainless ones to change out with the ome stainless ones that came with mine. The new ones I’ve got look like the color of yours. I like the way yours look.

 

I did swap them.
https://www.ebay.com/itm/112540323716

 

Those are the same ones I got. I’m going to put mine on in a couple of weeks. Going to put some strips of ppf under the flare gaskets while I’m doing it. Those look so much better that the ones that come with them.

 

Went to a local 4x4 meet and posed up for some pictures with friends.
Grey Tundra: stock suspension, 37s BFG KM3
Cement Tundra: IRONMAN4x4 suspension, 315/70r17 BFG KO2s
Black Tundra: Bilstein 6112/5160, 35x12.5r17 Geolandar M/T G003
Green Gladiator: stock suspension, 35s
White Power wagon: stock suspension, 37s BFG KO2
Silver Power wagon: some kind of suspension, 37s.

 

How are you fitting 37’s on stock suspension?

 

First off, I know. Seen all the TW stuff over the years. Bought a few things like the front Tacoma grab handle and bowl lights years ago before the shit show.

I've had them in my Tacoma for over two years and really like them. Thought about doing my own, even have all the leds and 5mm holders from other projects (since you have to buy a dozen-ish at a time) but they protrude out and wouldn't be a flush type finish and my (and any ones) fingers would catch on them going the DIY route since the stock bowl covers don't have a top surface to mount. Or they would face out making it a bit distracting driving at night.

Door Bowl Lighting - 3rd Gen Tundra - KTJO 4x4 they are 2.5 gen even though it says 3rd. You can tell by the bowl shape

Not trying to promote, but I'm a sucker for lights. Maybe someone else will enjoy

anyways

 

I don't know how my friend did it, but, most of it has to do with +25mm offset wheels, aftermarket bumper, and BMC + little bit of hammering I believe. He still rubs at full locks but apparently its drivable enough. just waiting for his kings to be rebuilt.

 

I bet he sweats bullets when he sees a pothole or a speed bump.

 

actually its not that bad, I have seen it in action.
here is a video of that truck off-roading