What have you done to your 2.5 gen Tundra today?

295/70s

Just under 35's

 

Do you have a lift on it? Or leveling kit? Any trimming need to be done?

Sorry for all the questions just need to get new tires soon and I like the look of your truck

Thanks
Edsel

 

Good read

https://www.tundras.com/threads/lar...for-all-generations.9762/page-11#post-2364102

https://www.tundras.com/threads/official-tundra-wheel-and-tire-setups-pics-and-info.95/

 

DIY'ed my solar setup on top of my LEER cap, free energy that runs my iceco fridge indefinitely.

 

2021 SR5 that came with an unlit driver window switch and only auto down feature.

Previously replaced the driver's window switch assembly to get auto up and down on driver window and lighted switch.

Then installed 3Wliners auto up/down module kit hoping it would work without running wire to battery. Probably expectedly, it didn't work and at the time I didn't want to take the time to run the wire to the battery. "Spoke" with @COTundie about what a pain it was to run the wire the right way, through the rubber boot that the factory door wiring uses. I didn't trust that I wouldn't jack something up so, full disclosure, I did not run the power wire to the battery through the boot. Instead, I fished it through where the door check and hinges are, into the front fender and up and around to the battery. Going to wrap with a little rubber sheathing to keep it from getting wet where it is exposed between the fender and door. If it lasts, great; if it doesn't I regroup.

In the meantime, now have the lighted driver side switch and auto up/down on all four windows and got the bonus of all four windows up and down from the remote. Doesn't replace the remote start feature but sure will help on those hot summer days when I can get a head start on cool down before I head out to the truck.

 

Not *today* but haven't had a chance to post, this past Friday I installed the Valhalla's Shield front and rear cat plates along with newly red powder coated front tow hooks.

 

Thank you John!!

 

How do you like the Victory winch bumper? Did you have any issues on the installation? What winch did you use? I was thinking about getting one this fall.

 

That be them as well.

 

I was considering doing this as well...do you think there is any issue with the components overheating/not having enough airflow?

 

The sensors for 2020 and newer are a different mhz.

 

So, I just did the carpet to the back of the amp, didn't actually cover the amp proper, for exactly that reason. I think the other sides exposed, and the carpet just being over the cables (so cables are providing some space under it), will leave sufficient airflow. Here's a picture with the seat all the way up, so you can see, maybe that'll help. But, I'm not an expert, so if any pros are seeing a red flag, let us know!

 

Actually may have to start driving like Grandma, seat all the way up and hugging the steering wheel, that looks pretty good...

 

Dang that’s clean.

 

I love it! I really try to keep the stock lines of the truck. No issues on install, their YouTube video was spot on. I have a Badlands 12k winch, used it twice so far, only using it to respool. I have a large yard on a slope, so it took my truck no problem that 100’. Before every off-road run I check it, and it always works.

 

Installed the softopper aka vacation mode activated

 

Installed 3.5 RC lift with 295/70r18

 

So are these plug and play or is there extra wires needed?

 

https://www.tundras.com/threads/any...n-1-touch-up-down-for-window-controls.106562/

Plug and Play. 10 min job.

 

Set my winch line under load and did a shakedown run of the new bumper suspension and tires

 

With a 3” OME lift can I run a 35x12.50r20 on scs 20x9 wheels?

 

Got it installed today. Works good and the blue lights match almost perfectly.

 

Looks good! Is your bumper rubbing the front filler piece? I always forget until I see photos how much flex there is.

 

probably not without significant rubbing

 

No bumper doesn't rub at alll.

 

I just put 325/60r20 which are basically 36s on mine, with a 2.25 dobinsons. It rubbed like crazy. Had to do bmc , pinch weld , and trim the shit out of the bumper plastic (prior to replacing the bumper) I'm on 20x9 +20 fuel

 

Damn it.

I currently have 34x11s and there’s so much damn room I figured they’d fit

 

What sensors?

 

Gotta remind her that while she may be pretty, she’s still a truck!

 

TPMS