What have you done to your 2.5 gen Tundra today?

Inside of left bumper, the plastic area that everybody trims is where it’s making contact on left side.
Already have bumper shins in there.

ReadyLift ProPlus2 with 18x9.5 +12 offset wheels. bfg 35x12.5r18 tires.

 

Mounted my SCS SR8 wheels with Cooper Rugged Treck Tires 275/70/18 (from 255’s). Had to remove the front mud flap as expected and the poke is the max I was looking for. Very pleased and haven’t really noticed any decrease in power from the heavier tires. Could be the swap for the lighter SCS wheel from my stock steel wheels that counteracted the heavier/larger tire.

 

Changed out Toyota Predator steps for AMP running boards. Always hated the way all steps look, not so anymore.

 

I agree. They look so much better without. Did you install yourself? Seems kind of involved

 

Yea - did myself. Really wasn't that bad. Which trigger wire to tap isn't correct in the instructions, which I think is the common complaint. I went with what someone else did in another thread for the '19 and it worked first try for me. I thought the biggest pain was installing the lights actually since the measurements they give weren't correct for the double cab and had to re-drill the front holes since I partially hit an expansion point around the pinch weld and the wire grommets were too small to span the gap.

 

Have a link to tray?

 

hopefully they can help it with alignment. thats a lot of offset and a wide tire. I bet it looks great! if the plastic wont go forward anymore no reason you couldnt do a little more bumper shim... after that its aftermarket bumpers. i dont think the plastic rub is a big deal but mine sounded like it would explode before I fixed it lol

 

Agree. I just thought it was odd that I was only getting into the bumper on the left side and not the right. With no body mount contact on that side. The right side is just the opposite, and from my pocketbook perspective, I’d rather deal with the bumper than the BMchop.

in any event, thanks for the feedback.

 

Got my falken wildpeaks today. 285/65/17 with bilstien 5100 in front top setting

 

Little milestone.

 

Mounted and wired my Baja Designs S8 and Diode Dynamics SS3 fogs.

 

That looks really nice! I too have the 5100s on the top setting and really thinking about putting the 2015 TRD Pro wheels on. Essentially the TRS Off-Road but all black and a TRD logo in the center like yours. This gives me good perspective on how they would look.

 

Nice, yep mine are 2021 TRD off road/limited wheel with TRD center caps I ordered


Edit : but I know the wheel you’re talking about. They’re beautiful

 

taillights look good - are they covers or aftermarket lights?

 

hi rev in black

 

or use only the fob of a aftermarket remote starter. I installed the receiver of the remote starter right beside the Saftey sense camera behind the back mirror and works better than the OEM fob.

 

Looks perfect! how's the ride quality?

 

that's some coin in lighting! Looks great

 

Honestly not a whole lot different. The bilsteins being on the third setting alone was a bigger change in ride/feeling.

 

I have the 26 gallon tank and had about 3/8” of lean. But I have Toytecs so I just adjusted the drivers side up to compensate, so didn’t need shims.

 

I had the same issue - mine would only rub in reverse on the driver’s side on the front liner. After I installed the JBA uppers and got more caster, I have no run at all but granted my tires aren’t as wide as yours either.

 

I have the bigger tank and I only drive the truck 2 or 3 days a week. It barely gets any miles on it and I still feel like Im getting gas all the time

 

yep it goes quick - especially at these prices

 

Swapped out the overhead console from a Sequoia for the conversation mirror:

 

Method 305s with 275/70/18 Cooper discoverer at3 xlt's installed today. Have a set of 5100's waiting for me to get some time to install as well. We got just under a foot of snow this weekend then today it was right around 0 lol. Didn't stay clean for long

 

That beats the business card holder, do you have a part number#?

 

30603

 

Are you reading that from right to left or left to right?

 

Looking for palindromes are one of the things that go with my nickname…