Show Off the 20x12 -44 Wheels and Tires

What lift do you have? Looks great

 

I'm running a 22"x12" -51 on a 37"x13.5" tire.

 

That looks Really Good!!!

 

I went with a 7" BDS Lift with the fox coil overs..

 

Yup I had same lift. 7" BDS with fox coils. I kept my fox shocks and sold the BDS lift though. I went with the pro comp lift because no one in town will warranty the BDS lift if it causes excessive tire wear. But with the pro comp 4 wheel parts could warranty the lift and insure proper allignment. I called BDS and talked to them and they told me the BDS lift for the Tundra has been known to wear tires faster for some reason. So although I had a 7" BDS on previous Tundra I went with a pro comp on this truck for warranty and service reasons. BDS still makes a great lift.

 

Interesting, does the same thing apply to the BDS 4.5" lift? I've been looking at going that route for my truck.. might steer me away if that's the case.

 

Fuel Cleaver 20x12 -44 w/ 37" Ridge Grapplers, Sorry not a good angle, will try to take a different one soon

 

I doubt you will have any issue with the 4.5" BDS lift. I was referring to the 7" lift.

 

Gotcha! I thought you were talking about BDS lifts on the Tundra in general, my bad.

Good looking rig!

 

That is good info to know and Thank you.. I was told if you do aftermarket upper control arms that would fix that problem because you have more travel room with the aftermarket upper control arms. My last set of tires wore even just wore out super fast...I got 22k out of them. I thought it was just because I had the Nitto mud extreme tires the tread pattern was so aggressive.

 

Old Wheels and Tires.... 20x12-44

 

Good looking Truck!!!!

 

Aftermarket control arms will definitely help with alignment and the bigger offset wheels. I still like BDS lifts. The pro comp was just a better choice for my setup. The nitto muds are a very loud and fat wearing tire because they have big spacing between the tire pattern.

Here is a pic of my 2012 Tundra with a 7" BDS lift (non coil over), 20"x12" Fuel Nutz wheels & 35" tires. I didn't have any excessive tire wear on that truck. I also had stock Upper a arms.

 

Looks good. You have to be getting 10mpg with 37s

 

XD 825 20x12 -44 offset Toyo mt 37x13.5

 

Good looking RiG!!!!!!

 

How high is that? Looks nice .

 

Thanks it's just about 8" of lift.

 

Anyone else running this size? Thinking of changing up my setup

 

Looking for more pics of 20X12 -44. Looking at getting some right quick, just don't want to stick out too much.

I have a ~7" lift and bushwacker fender flares.

 

This is from custom offsets

 

Anyone on this thread have issues with bearings or joints running 20x12s I’m doing a 7”bds lift on my 2017 Crewmax and I want to go with the 22x12 -44 Fuel Sledge wheels just don’t want to have issues down the road.

 

Im 22x10 and -25 offset with 7 inch BDS. No issues

 

Did you have to do any cutting for the 7in?

 

I cut the body mount and had the weld plate installed to help with clearance. It’s on my build page.

 

I'm in the middle of tire wear issues I think alignment wasn't near close when I had it done and ... took it to an old school alignment guy and he said steering rack bushings need to be changed and he can make it perfect i also have the 7" bds... its possible to get alignment on then ??