FS Phx AZ: TSS Wheels & Tires *SOLD*

PM me for additional info; local pick up only.

Removed from my truck at approximately 35-36k miles

2017 1794 OEM front end parts: Sold
hood bulge, grill, bumper (both cover and crash bumper) w/end caps and fog lights (end caps have sensor spots but sensors not included), headlights w/bulbs (these are the factory 1794 headlights that have the DRL led lower strip) $400 for complete list (willing to price individually if needed)**Limited Grill not 1794** (good callout @AZBoatHauler)

4 Toyota TSS 20x9 +50 offset: Sold grey with machined lip wheels (lugs and center caps included); 4 Nitto Ridge Grappler 285x60R20 (33x11.5) tires w/~11/32” tread remaining (~20k miles on tires). Tires are not mounted on wheels currently as were removed to switch over TPM Sensors (i.e.sensors are not included in sale) $800 700 for complete wheel/tire set; $550 500 just Wheels/$350 300 Tires; not looking to piece out individual wheels or tires (sets only)

Rough Country Black Series Single Row 30” LED lightbar w/DRL mounted on Rago Fab Stealth Mounts for lower bumper; original hardware included ~12 months old. Minimal use; no damage. Will need a wire harness/relay/switch to connect after rough country pigtail connection. $150 *Original harness /relays and 3-way switch included*
Sold

 

Damn, great price on wheels. I might be interested in those too.

 

Thanks—trying to price the stuff to sell to get it out of my garage at what I think is a good deal.

 

Any damage on the wheels? Got more pics of them installed? Were you running spacers behind them?

 

No spacers; never repaired/refinished; not bent/damaged. Minor cosmetic wear…should be viewable in pics, IMO kind of exaggerated as the pics will be more up close/flat/no tires versus when vertical on a vehicle not really noticeable. Placed a penny for size by one paint chip; the one has less than an inch long curb scratch, but it has been there since I bought it. I circled it in green in the last photo that shows the tires that were on it originally when I bought it.

 

Installed when I had dealership change out the tires on delivery and a couple other photos; last photo is with new 35s before switching to my new wheels that arrived 2 weeks later (you’ll notice the red TRD pro suspension boot too, which was the start of my suspension/wheel change out)

 

I'm interested. Wasn't my first choice but these will definitely do until I get my bronze 17's on 37's which should be next year. I'll message you.

 

Isn’t that a Limited grill?

 

Would you be willing to sell just the brackets?

 

You’re right. Ironically, I’ve had my truck since spring ‘18 (2nd owner purchased from dealership) and always just assumed it was the stock 1794 grill because of the chrome surround and knew it wasn’t a SR5 or Pro grill. It had other TRD accessories and the TSS wheels, so must’ve been swapped by prior owner.

 

Keeping it together as of now, if it doesn’t sell together shortly, I’ll let you know.

 

What you gonna put down there?

 

I’ve already got an Amazon bar there, just shitty Amazon brackets. And it looks like the Rago mounts allow you to mount further forward which is really what I’m wanting.

 

Understood and sounds good.

 

My new bumper had a double row cutout so I put in a new laser led lightbar from SDlighting (local company here in AZ)

 

Looks good

 

I've heard of them, most of their stuff is meant for ATVs. How do you like the bar?

 

@TucsonTundra1794 it’s really bright. Nice quality; was trying to decide if I just went with the rough country again in the dual row. I decided to support local, and I could pick it up same day, which helped with finishing my project out.

 

Sweet! Post some output shots if you have some. I have a few different brands but no experience with theirs.

 

I posted previously:
https://www.tundras.com/threads/wha...d-gen-tundra-today.713/page-2053#post-2353720

 

1794 Front end parts sold…edited with strike-through in 1st post.

 

That looks good. The single row 44” might work well in my hood bulge like I’m planning… how was the RC bar in your old bumper though? Maybe that’ll be better than my current one.

 

Ha, I read that previous post and had thought it was the BD laser bar. I thought this was a different bar.

 

Let me know when you sell the light bar. I have a brand new harness that fits that connector. I'll take pics of it later today.

 

There light looks a little big, I'd measure before committing. I haven't wired up my RC bar but I did test it and it's pretty bright, definitely enough to light up down low and decent way down the road. My 20" S8 out shines it but the RC outshines the nilight Amazon ones.

 

Yeah you’re right. I couldn’t remember if it was 42 or 44 on the width in the bulge, but looks like 42 is the biggest that will fit.

 

A 44" is too long. A 40" is the common if you don't get the NSV. The 40" BD S8 will have just under 1/2 gap at each end.

 

@TRDFerguson
The rough country light is more than enough light on high mode—it casts way beyond my brights on my headlights and lights everything up. Definitely an off-road or night forest highway light as it’ll blind any oncoming traffic. The low setting can be used as a DRL. I have a pic of it on in my original post, but it’s during the day, so hard to really determine the output. I don’t think you’ll get a better light without spending big $ on a rigid or Baja design. I had tried a cheap Amazon light originally…thread holes that mount to the bracket stripped out under tension before ever getting to use it. Rough Country is definitely better quality built and really nice Cree LEDs…black LED housing is also cool in my opinion for the more subtle stealth look when not powered on.

 

Here is another members S8 that took pics for me.

 

Thanks! Adding picture of where I cut; does yours use the same connector? I left enough excess wire that any harness should be able to be connected, but would be nice to have the plug and play original for new prospective buyer.