What have you done to your 2.5 gen Tundra today?

Love my amp steps!

 

I was able to finish up thr rear bumper and swing-out flagpole holder just in time for a local meet.

 

Washed it and put on some red smoked Spyder tail lights.

 

Normal

 

There's a reason they were banned from here lol

Check the thread on her products. A few folks have provided instructions that might help you

 

Just my second post but I temped up the data monster and hooked it to the pedal monster. I had the pedal commander for around nine months. It feels like it shifts smoother with the pedal monster. I will build a custom gauge pod and add two more gauges also.

 

Finally for the double cab. It's just me and the wife so the back seats stay up 100% of the time. I was never happy with the Husky Exact fit for the back. At least it news to me but someone post this Husky a couple weeks ago. Much better coverage when seats are up.

 

Congrats....We have 4 as well...25, 22, 20, and 16 boys are the bookends.

 

That's not a bad spot. I had a few of those gauges left over from the sale of my F150 and tried a few different spots in the Tundra before settling on the CravenSpeed gauge mount. (Side note, the 2015 F150 Platinum was super fancy, but I love this 2020 TRDPro so much more for some reason.) It required a little modification (grinding and painting) to accommodate the large bezel of the Banks gauges, but I think it turned out pretty good. Here's a pic just after getting it installed. I'm still figuring out what PIDs I want displayed. The bummer thing is that the trans temp isn't available.

$115 CravenSpeed FlexPod Gauge Mount Compatible with Toyota Tundra 2007-2021

https://www.amazon.com/gp/product/B008G5552E?ie=UTF8

 

Yes, I would like the trans temp looks like I will have to add the 5 Ch analog with Frequency Module for Datamonster from Banks and a trans temp probe.

https://www.bankspower.com/i-2843-5...|make=TOYOTA||model=TUNDRA||submodel=5.7L GAS

 

Not to be a stalker, but didn’t you have 285 75 17 before? I’m curious how different it feels. Looks great!

 

PM’d ya

 

Yes, I had 285/75/17s. Great size tire, by the way!

I do feel a subtle difference during acceleration and braking. They’re obviously heavier and wider, even though they’re only about 1/2” bigger in diameter. I’m sure a re-gear would help, too.

I’m hoping to try them out off-road on some off camber trails and see if there’s a more notable improvement, especially with the slightly wider tread. And while they’re not as cool looking as true 35’s or even 37’s, they still look pretty cool to me!

 

We also have 4. 4 boys, 22, 18, 15 and 2. It was a cold night 2 years ago if you're wondering why the big gap for #4.

 

I was in a similar spot. I was unhappy with the rear coverage for the DC. I have the underseat storage, so I thought it was my only option. Then I saw @glowblue, I think, selling their mats and had full rear coverage with underseat storage. I immediately ordered a new rear and replaced it lol.

 

Is this what Husky calls “full coverage mat” model 19561 for double cabs? I’m interested in this myself.

 

I ordered #53851, since I have X-acts. #19561 is the Weatherbeater variant. What the difference is? Honestly I do not know. X-acts are a nice soft rubber material. I believe the Weatherbeaters might be a harder "plastic" like material, but I'm not certain. And they say full coverage, but it doesn't go all the way to the back of the cab, it stops roughly half way under the seat.

 

you're correct. the weatherbeaters suck.

 

First part of a series of videos about the Tesla Style radio unboxing, content, test, install, review, and more...

https://youtu.be/R7Dl9-WX5Kc

 

Got it, thanks!

 

Dig your videos, dude.

 

Thanks!

 

Just added a few more scrapes to the
skids!!!

 

Pretty cool. Where is that?

 

Top of the World Trail Moab, Utah

 

Color matched, 2K cleared, and mounted the high lift.

 

Wet Sanded down tail lights. 2 coats of VHT night shades then 8 coats of clear. Wet Sanded them down again. Then hit them with compound and medium cutting pad. Then jet seal with light cutting pad and 2 coats of butter wax. Came out pretty good. Thank you @TucsonTundra1794 for the drivers side tail light!

 

Those turned out great!

 

Thank you sir! Little time but I think it was worth it

 

Great work on the lights, not so great on covering license plate tho…lol