What have you done to your 2.5 gen Tundra today?

Um... if it's that expensive, then him cutting you a break on the body work really isn't a break at all.

 

Ya you are 100% right. My tail gate had a ripple in it with a good crease so I was looking at having to buy a new tail gate. He did it for 50$ and made it look like new. But if I need a new camera it’s gonna be a wash.

 

The combo of both TRD bars compliments themselves. The factory front leaves alot to be desired.

 

It's an M6 x 1.0

 

So I cut and drilled the stick and hit it with a couple of quick coats just to get an idea of the results.

 

looks good!

 

what material did you use? Looks good!

 

Are you going to cut a hole to access the spare tire or are you going to remove that cover when you have to get to the spare tire?

 

I'm most likely going to put it in the bed.

 

1.5 inch wide by 1/8 thick aluminum stick.from Lowes.

 

We must use the same doctor

 

Kudos on that one. Looks great! Especially if you’re putting the spare in the bed.

 

I love this idea. For me matte black would probably blend the best, but that’s beside the point.

What about the super duty velcro they sell? Could possibly add that and make it fully removable to access the spare.. just speculating.

 

https://www.youtube.com/watch?v=Lrd25ZKceqU&feature=youtu.be Added my new outlaw exhaust today, sounds great!

 

@DCB500 You're missing a washer on your end links...this was discussed here on this thread.

https://www.tundras.com/threads/another-trd-rear-sway-bar-install-question.78953/#post-1998511

Starting on either side, mount the RSB onto both End Links using the following hardware configuration (19mm hex): M12 bolt, washer, end link, sway bar, washer & locknut. The sway bar mounts inboard of the end links (Fig. 4-1).



See attached.

 

damn I sure did....easy fix, thanks for the heads up!

 

Thanks for the info appreciate it.

 

Added CPlay2 to the truck. Works pretty well. Wireless CarPlay.

 

Got the truck protected and coated today

 

Installed RB20 running boards, and Weather Tech window vents today.

 

What'd you use?

 

Has your RC rear bumper also started rusting after a few months?

 

What light is that between the tailgate and bumper?

 

Finally got a day with more than an hour without rain so I took advantage and washed and treated the truck with some Griot's 3-in-1.
Also hit the plastics and tires with Adam's VRT. Both great products, highly recommend both. The VRT on the bumper treads, bed caps and front bumper make a huge difference!

 

Where did you get your SABM kit from?

 

I got 2 of the mounting plates. I also put some high temp silicone I had laying around to seal any possible air gaps.

Spectre Performance SPE-8148 8148 Air Duct Mounting Plate

$9 Spectre Performance SPE-8148 8148 Air Duct Mounting Plate

https://smile.amazon.com/dp/B000BPU...abc_61P077BSKN779YMXGQC2?_encoding=UTF8&psc=1

Spectre Performance 8771 3-3/2.5" Intake Coupler

$13 Spectre Performance 8771 3-3/2.5" Intake Coupler, Black, 3 x 3" "

https://smile.amazon.com/dp/B0008G5...abc_5D15SHW31TVTBYV46EGD?_encoding=UTF8&psc=1

LENOX Tools Hole Saw with Arbor, Speed Slot, 3-Inch (1772963)

$25 LENOX Tools Hole Saw with Arbor, Speed Slot, 3" (1772963)

https://smile.amazon.com/dp/B004YK5...abc_SXV1A4Y4S6WG6D5MF8KN?_encoding=UTF8&psc=1

Permatex 81160 High-Temp Red RTV Silicone Gasket, 3 oz

$11 Permatex 81160 High-Temp Red RTV Silicone Gasket, 3 oz

https://smile.amazon.com/dp/B0002UEN1A/ref=cm_sw_r_cp_api_glt_fabc_5KGM98WZC7C192JMVS37

 

Nope, I have had no issues with it and have the matching front RC Bumper as well. Live in El Paso with very little rain or moisture so that may have something to do with it. Both have been installed for little over a year now.

 

Is it possible to install the RC intake tube into the air filter box?