1. Welcome to Tundras.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tundra discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Tundra owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Looking for MAF sensor cleaning advice

Discussion in '1st Gen Tundras (2000-2006)' started by Black '00 Tundra, Oct 8, 2020.

  1. Oct 8, 2020 at 1:20 PM
    #1
    Black '00 Tundra

    Black '00 Tundra [OP] New Member

    Joined:
    Jun 28, 2019
    Member:
    #32537
    Messages:
    43
    Gender:
    Male
    First Name:
    Micah
    Vehicle:
    Beefy black man-wagon
    Hello forum. I was having really bad stumbling/hesitation issue while it was idling, while taking off from a stop, and even while maintaining a constant speed at freeway speeds. It was getting worse and worse until I finally got tired of it, did some research, and decided that cleaning the MAF sensor and throttle body butterfly valve was the most likely way to fix this.

    Well I cleaned both things, and the problem almost went away, but the stumbling/hesitation issue is still there it's just far less intense than it was before. It's about 25% as intense as it used to be. I could live with this but I want it nice and perfect again. Let alone the gas mileage I'm missing out on having the air/fuel ratio going cattywompus all the time must be costing me money in fuel.

    My question is: Can I clean the MAF sensor elements with more than just blasting it with MAF sensor cleaner from a can? Will I damage those little sensors if I use a small, fine-bristled brush (like a toothbrush or something even smaller) along with more MAF sensor cleaning solution?

    Edit (12/29/20): This issue was eventually solved. The stumble/hesitation/misfire issue was fixed 75% of the way by replacing the MAF with a new one. The other 25% of this issue was fixed by replacing all 8 ignition coils and all 8 spark plugs. Replacing the fuel injectors made no difference at all.
     
    Last edited: Dec 29, 2020
    huntsonora likes this.
  2. Oct 8, 2020 at 1:29 PM
    #2
    Black '00 Tundra

    Black '00 Tundra [OP] New Member

    Joined:
    Jun 28, 2019
    Member:
    #32537
    Messages:
    43
    Gender:
    Male
    First Name:
    Micah
    Vehicle:
    Beefy black man-wagon
    I took macro pictures of the sensor before and after spraying it real good with CRC Mass Airflow cleaner. The picture that looks less dirty is actually the before picture. There was a fine layer of dust-like material that was washed off. But if I get in there with a brush and more solvent, I can get it a hell of a lot cleaner than that.
     
    Tierhog likes this.
  3. Oct 8, 2020 at 2:53 PM
    #3
    Professional Hand Model

    Professional Hand Model A.K.A ‘Golden Hands’

    Joined:
    Apr 29, 2018
    Member:
    #14878
    Messages:
    15,007
    Gender:
    Male
    First Name:
    Fred
    ‘Somewhere’... a State of Mind
    Vehicle:
    2002 Tundra SR5 4WD 4.7L AC Silver Metallica
    Hand Protectors
    Go to Hitachi Store on the biggest retail website in the world and buy a new one. My 4.7L 2002 MAF was out of spec due to age and I asssume yours might be, as well. Hitachi makes Toyota MAF and they scratch the Toy name off due to branding issues. $50 vs 150.

    I cleaned my old one with spray and it still wouldn’t get all the cack off (similar to yours). Used a Digital Meter and tested the spec OHMs and they were off so went and bought a new one. I’d not use any type of brush to clean your old one. Buy new.

    upload_2020-10-8_17-53-29.jpg
     
    Rdway60, Stumplifter, bmf4069 and 3 others like this.
  4. Oct 8, 2020 at 3:03 PM
    #4
    Black Wolf

    Black Wolf Bigfoot Hunter, Sasquatch too, but not Yeti

    Joined:
    Apr 20, 2014
    Member:
    #378
    Messages:
    40,012
    Gender:
    Male
    First Name:
    Matt
    Aurora CO
    Vehicle:
    2022 Nissan Frontier SV 4X4
    TuwaPro rack, Z1 Offroad stuff, NISMO suspension stuff, FlowmasterFX Extreme exhaust, AIS, OVS, J&L can, other goodies on the way
    This^^^^
     
  5. Oct 8, 2020 at 3:08 PM
    #5
    omgboost

    omgboost The Accountant

    Joined:
    Apr 19, 2019
    Member:
    #29334
    Messages:
    1,087
    Gender:
    Male
    East Coast
    Vehicle:
    2012 Sequoia Platinum
    Buy a new one, try your way and see if it works. If it does, report back. If it doesn't, you have a new one ready to swap in.
     
  6. Oct 8, 2020 at 3:49 PM
    #6
    Black '00 Tundra

    Black '00 Tundra [OP] New Member

    Joined:
    Jun 28, 2019
    Member:
    #32537
    Messages:
    43
    Gender:
    Male
    First Name:
    Micah
    Vehicle:
    Beefy black man-wagon
    Yes! Awesome tip. I just went over there and found that exact sensor, MAF 0048, and ordered it. $55 with free shipping. Boo-yah! It's supposed to be here Saturday. I'll give an update soon.

    Hey just for good measure, would you guys recommend replacing the O2 sensor too? Like maybe if the ECU is reading the wrong amount of oxygen in the exhaust, that might exacerbate air/fuel ratio issues caused by the MAF?
     
  7. Oct 8, 2020 at 3:52 PM
    #7
    Rex Kramer

    Rex Kramer Vinyl Spinner

    Joined:
    Apr 9, 2017
    Member:
    #7181
    Messages:
    6,620
    Gender:
    Male
    Georgia
    Vehicle:
    2002 4.7L RCLB 4X4 2007 5.7L RCSB 4X2
  8. Oct 8, 2020 at 4:01 PM
    #8
    Professional Hand Model

    Professional Hand Model A.K.A ‘Golden Hands’

    Joined:
    Apr 29, 2018
    Member:
    #14878
    Messages:
    15,007
    Gender:
    Male
    First Name:
    Fred
    ‘Somewhere’... a State of Mind
    Vehicle:
    2002 Tundra SR5 4WD 4.7L AC Silver Metallica
    Hand Protectors
    Yeah. I replaced all 4 of my o2 sensors at the same time as the MAF Sensor. My fronts were replaced about 8 years ago with Bosch by a shop. They were out of spec. My rears looked to be original Toyota. Those were out of spec, as well.

    Go back to that website to the Denso Store and order all 4 New o2 Sensors. They run about $50 each. My truck runs so much better. The torque and engine response after is insanely better if yours were old like mine.

    Buy a thread chaser and o2 Socket to make things easy. You’ll need 4 new nuts for the rear.

    upload_2020-10-8_18-59-1.jpg

    upload_2020-10-8_19-0-41.jpg

    upload_2020-10-8_19-1-16.jpg
     
    Schcoman, N84434 and FirstGenVol like this.
  9. Oct 8, 2020 at 7:36 PM
    #9
    CodyP

    CodyP Such a n00b

    Joined:
    Oct 27, 2018
    Member:
    #21047
    Messages:
    3,038
    Gender:
    Male
    First Name:
    Cody
    CDA, ID
    Vehicle:
    2006 Tundra 4x4 DC
    Where is this voodoo cheap hitachi store you speak of @Professional Hand Model
     
  10. Oct 8, 2020 at 7:40 PM
    #10
    CodyP

    CodyP Such a n00b

    Joined:
    Oct 27, 2018
    Member:
    #21047
    Messages:
    3,038
    Gender:
    Male
    First Name:
    Cody
    CDA, ID
    Vehicle:
    2006 Tundra 4x4 DC
    Dammit, did I miss another big guurl reference?
     
  11. Oct 8, 2020 at 11:21 PM
    #11
    artsr2002

    artsr2002 2005 Tundra DC SR5

    Joined:
    Sep 2, 2019
    Member:
    #35520
    Messages:
    1,756
    'Yonder
    Vehicle:
    Red-Maroon-Something 05 DC 4.7 4x2
  12. Oct 8, 2020 at 11:24 PM
    #12
    artsr2002

    artsr2002 2005 Tundra DC SR5

    Joined:
    Sep 2, 2019
    Member:
    #35520
    Messages:
    1,756
    'Yonder
    Vehicle:
    Red-Maroon-Something 05 DC 4.7 4x2
  13. Oct 9, 2020 at 4:12 AM
    #13
    tvpierce

    tvpierce Formerly New Member

    Joined:
    May 6, 2019
    Member:
    #30129
    Messages:
    1,261
    Maine
    Vehicle:
    2000 Tundra AC SR5 4WD, 4.7 Automatic
    Keywords: LIGHTEST POSSIBLE TOUCH, GENTLE TOUCH, BEARLY TOUCHING
    (Just put that at the top so some ham-fisted knuckle-head doesn't reference this post and miss the most important part.)

    I hesitate to give this advice because if you're not really gentle with the cleaning, you could possibly damage your MAF sensor. But here goes:

    I've had the same experience as the OP with MAF sensors on my Tundra and other vehicles. The spray cleans the majority of the gunk off, but it's clear that there's still residue left on the elements. So what I do is soak the end of a Q-tip with MAF sensor cleaner and WITH THE LIGHTEST TOUCH POSSIBLE, JUST BARELY TOUCHING THE SENSORS, I thoroughy clean them with the Q-tip. Imagine you're using that Q-tip to try to clean a strand of a spider web -- that's how careful you need to be. Go gently and slowly, then rinse with a good blast or two of MAF sensor cleaner.

    It works really well.:thumbsup:

    Now if you test it and it's not in spec, all the cleaning in the world isn't going to help... just replace it.
     
    Last edited: Jan 5, 2023
  14. Oct 9, 2020 at 4:20 AM
    #14
    tvpierce

    tvpierce Formerly New Member

    Joined:
    May 6, 2019
    Member:
    #30129
    Messages:
    1,261
    Maine
    Vehicle:
    2000 Tundra AC SR5 4WD, 4.7 Automatic
    I can't stand that guy.:rolleyes:
     
    RJVA, Saltyhero13, Grumpy74 and 2 others like this.
  15. Oct 9, 2020 at 4:44 AM
    #15
    Rex Kramer

    Rex Kramer Vinyl Spinner

    Joined:
    Apr 9, 2017
    Member:
    #7181
    Messages:
    6,620
    Gender:
    Male
    Georgia
    Vehicle:
    2002 4.7L RCLB 4X4 2007 5.7L RCSB 4X2
    He is a valid source of information.
     
  16. Oct 9, 2020 at 4:56 AM
    #16
    artsr2002

    artsr2002 2005 Tundra DC SR5

    Joined:
    Sep 2, 2019
    Member:
    #35520
    Messages:
    1,756
    'Yonder
    Vehicle:
    Red-Maroon-Something 05 DC 4.7 4x2
    Bearly touch it though.

    bearly.jpg
     
    Darkness, bmf4069, Lil Steve and 4 others like this.
  17. Oct 9, 2020 at 6:38 AM
    #17
    tvpierce

    tvpierce Formerly New Member

    Joined:
    May 6, 2019
    Member:
    #30129
    Messages:
    1,261
    Maine
    Vehicle:
    2000 Tundra AC SR5 4WD, 4.7 Automatic
    :rofl:

    Good catch!
     
  18. Oct 9, 2020 at 7:24 AM
    #18
    FirstGenVol

    FirstGenVol Brake Czar

    Joined:
    Dec 13, 2018
    Member:
    #22934
    Messages:
    12,911
    East TN
    Vehicle:
    2002 AC
  19. Oct 9, 2020 at 7:26 AM
    #19
    Tierhog

    Tierhog SIG-AHOLIC

    Joined:
    Feb 7, 2018
    Member:
    #12731
    Messages:
    1,200
    Gender:
    Male
    First Name:
    Steve
    Florida
    Vehicle:
    2016 Tundra Crewmax Limited 4WD
    Mostly stock/TRD accessories/Morimoto XBs
     
  20. Oct 9, 2020 at 11:37 AM
    #20
    bmf4069

    bmf4069 Yup, that's car parts in a dishwasher

    Joined:
    Sep 1, 2018
    Member:
    #18880
    Messages:
    7,273
    Gender:
    Male
    TX
    Vehicle:
    02 AC sr5 4wd v8
    So what you're saying is me and @FirstGenVol shouldnt use this method?
     
  21. Oct 9, 2020 at 12:37 PM
    #21
    tvpierce

    tvpierce Formerly New Member

    Joined:
    May 6, 2019
    Member:
    #30129
    Messages:
    1,261
    Maine
    Vehicle:
    2000 Tundra AC SR5 4WD, 4.7 Automatic
    :rofl:

    Instructions for you two:
    Soak the head of your 5 pound sledge hammer with MAF cleaner, and give the MAF sensor a gentle tap.

    :D
     
  22. Oct 9, 2020 at 12:48 PM
    #22
    Rex Kramer

    Rex Kramer Vinyl Spinner

    Joined:
    Apr 9, 2017
    Member:
    #7181
    Messages:
    6,620
    Gender:
    Male
    Georgia
    Vehicle:
    2002 4.7L RCLB 4X4 2007 5.7L RCSB 4X2
    Earlier this year I cleaned the MAF & TB on both trucks, my fingers don't always function 100% and I ended up dropping the MAF for the 2002 while cleaning it. I picked it up of the grass, sprayed it with cleaner again, and installed it after drying... it works just fine.

    IMG_7792.jpg
     
    270Fan, MS22, bmf4069 and 1 other person like this.
  23. Oct 9, 2020 at 2:10 PM
    #23
    rock climber

    rock climber New Member

    Joined:
    Oct 7, 2019
    Member:
    #37106
    Messages:
    1,601
    Gender:
    Male
    Colorado
    Vehicle:
    2001 Sequoia 4X4, 2000 AC 4X4
    Depending on how dirty you throttle body was, it may make sense to unbolt it and clean the backside also. I thought I had cleaned mine really well, but then I had to pull it to replace the throttle position sensor and I was surprised how much gunk was still there.

    Have you also checked your spark plugs and air filter?
     
    Rex Kramer likes this.
  24. Oct 9, 2020 at 2:11 PM
    #24
    robabeatle

    robabeatle New Member

    Joined:
    Jun 14, 2020
    Member:
    #47947
    Messages:
    826
    Gender:
    Male
    AZ
    Vehicle:
    2002 Tundra 4x4 LTD AC
    Bilstein 6112 & 5160, Katskinz, audio upgrades
    This thread caused me to pick up TB and MAF cleaner today.
     
  25. Oct 9, 2020 at 2:43 PM
    #25
    FrenchToasty

    FrenchToasty The Desert rat, 6 lug enthusiast

    Joined:
    Sep 15, 2019
    Member:
    #36156
    Messages:
    15,435
    First Name:
    Mo
    The SoAz
    Vehicle:
    2006 DC 4.88s Elocker and some other trippy stuff
    None
    I just did our 4runner over the weekend
     
  26. Oct 10, 2020 at 11:05 AM
    #26
    Professional Hand Model

    Professional Hand Model A.K.A ‘Golden Hands’

    Joined:
    Apr 29, 2018
    Member:
    #14878
    Messages:
    15,007
    Gender:
    Male
    First Name:
    Fred
    ‘Somewhere’... a State of Mind
    Vehicle:
    2002 Tundra SR5 4WD 4.7L AC Silver Metallica
    Hand Protectors
    Ours come with a cover. If you look closely on yours you will see it. It pops off and can be painted. Snaps back on the new one.
     
    FirstGenVol[QUOTED] likes this.
  27. Oct 11, 2020 at 3:31 PM
    #27
    tvpierce

    tvpierce Formerly New Member

    Joined:
    May 6, 2019
    Member:
    #30129
    Messages:
    1,261
    Maine
    Vehicle:
    2000 Tundra AC SR5 4WD, 4.7 Automatic
    I find his videos lacking in substance. And his delivery, to me, is like nails on a blackboard.
     
    RJVA, Stumplifter and FirstGenVol like this.
  28. Oct 11, 2020 at 5:38 PM
    #28
    peanut

    peanut making uneconomical choices about my truck

    Joined:
    Aug 24, 2020
    Member:
    #51249
    Messages:
    183
    Vehicle:
    2001 Tundra 4x4 V8 Access cab 222k miles

    +1 to that. It was the worst behind the throttle plate on mine.
     
  29. Oct 14, 2020 at 5:00 PM
    #29
    Black '00 Tundra

    Black '00 Tundra [OP] New Member

    Joined:
    Jun 28, 2019
    Member:
    #32537
    Messages:
    43
    Gender:
    Male
    First Name:
    Micah
    Vehicle:
    Beefy black man-wagon
    Ha ha, yeah really, me too. I know that guy's videos are full of great automotive information, but for some reason his personality makes me want to punch him in the face. Plus his nasaly, high-pitched voice makes my skin crawl. I'd rather listen to a cat being strangled. I'd rather listen to a baby elephant getting ripped apart by hyenas.

    I didn't try using a small brush on the MAF sensor, I just bought that exact replacement mentioned earlier in this thread and installed it. I STILL have a slight hesitation/stumble/misfire sensation every once in a while, but it's now about 90% better than it used to be. I reckon I will be back to 100% better once I replace all 4 oxygen sensors. Thanks for your help everyone!
     
    RJVA, bassman417, Stumplifter and 3 others like this.
  30. Oct 15, 2020 at 5:55 AM
    #30
    Stumplifter

    Stumplifter New Member

    Joined:
    Dec 23, 2019
    Member:
    #40243
    Messages:
    14
    Gender:
    Male
    Milwaukee, WI
    Vehicle:
    2006 Tundra Limited Double Cab
    None.
    I’m thinking I should get one also. Everyone is going to buy them out and there won’t be any left! :eek2:

    Just like toilet paper earlier this year... o_O
     
    bassman417, bmf4069 and CodyP like this.

Products Discussed in

To Top