Looking for pics of your 3rd gen Tundra with just a leveling kit, wheels, and tires. Thanks.

Looking for pics of your 3rd gen Tundra with just a leveling kit, wheels, and tires. Especially trying to see how big I can go on the wheels and tires with just a leveling kit. Thanks.

 

275.65.18 18x9 +12mm, Level kit 2/0

295.70.18 AT3 XLT

 

Nice! What's your wheels and tires setup?

 

18x9 +12
275.65.18

 

Planning on just a 2" leveling kit for the front. I'd like to go 35's but I doubt they'd fit. Minimum 33's though.

 

Bilstein 5100’s on mid setting.
Falken Wildpeaks 275/70
Vision Nemisis 18x9 +18 offset

 

Still running factory rims and tires, but have a 3/2 lift level. I left one spacer out on the fronts so it’s still has a small rake to the front. It’s an inch difference from front to back.

 

I’m running 33s with no lift at all. So you should be able to fit bigger with a leveling kit.

 

I went with Bilstein 5100’s middle setting up front only. Vision Fury 8.5x18 wheels +25 offset on BFG 275/70/18. No issues.

 

6112/5100 @ top setting, +3 CB shackles, Firestone Airbags, 275/65/20 Cooper AT3 XLT on stock wheels. I have a 0.75” rake. Tires rubs on front sway bar at full lock.

 

Readylift 3/1 level kit

ReadyLift 69-5175 Lift Kit

$326 ReadyLift 69-5175 3"F / 1"R SST Lift Kit - Toyota Tundra TRD / SR5 / Rock Warrior

https://www.amazon.com/dp/B00IOYREIK/ref=cm_sw_r_cp_apip_GX5AP6d1FaAH5

35x11.5 ridge grapplers

Barely misses cab mount but no cutting of metal

Slight trim to fender liner behind bumper, could probably use a heat gun and massage it instead

+20 wheel offset on 20 inch wheels

 

Bilstein 612's up front on second to highest setting which I believe is 1.9 inches. Bilstein 5160's in the rear set the same as stock. 2019 TRD Pro wheels.

 

2.5 leveling kit up front. 33 inch tires were the biggest I could fit with the +18mm offset wheels.

 

35 inch tires no rubbing with just a leveling kit

 

Bilstein 5100, middle setting
Ray 10s with 295 70 r18

 

Toytec Boss, Toytec Shackle on the top setting, SCS Ray 10, 28570R18 Ridge Grappler

 

I leveled mine by hanging the leaf packs under the axle, and I plan to run 33" tires this fall. Pictured here with 32" tires.

 

Leveled with 6112’s at 2.5”. Rear 5160’s. No shackles yet, but my front is 1” higher than rear. Running Icon 17” with 315/70/r17 with no BMC, just front mud flaps removed. No rubbing, but I am also running a RCI skid plate.

 

5100's front on middle setting along with coach builder shim. 5100's rear with 1" rear block, rding on stock wheels and tires.

 

17” fit on those? what’s the offset?

 

Your bumper- the middle part- is it finished in something other than plastic? It looks almost like dark gray, and shiny like paint..?

 

Icon rebound 17” has 25mm offset.

 

Here's a shot of my former 2014. Leveling kit only, with tires and rims.

 

6112s set at 1.9 front, 5100s rear no lift running 285/70/18 Yoko’s MTs on Methods +25.

 

Boss kit at full 3", 285/75r18 Nitto Terra's on stock rims. I had to cut away part of the bumper and use spacers to make it work. Also had to add the UCA's. I would have done wheels, but my budget manager cut my funds

 

What offset did you go with on the wheels?

 

285/55/20s. -1mm offset IIRC. I'd like a bit more sidewall sometimes but for a mainly street ride it isn't important. Leveled with Bilstein 5100s. Ground is off level in the pic, but truck sits level on flat ground. Later I had to remove short front of tire mud flaps, one side rubbed hard. Tires stick out an inch or so. I can get you a getter shot of it's stance if you want.

 

2" spacer lift . Stock rear
295/70/18 Nitto Ridge Grapplers on factory 18' . Sorry I know you wanted after market wheels but I liked my stock wheels and therefore able to run a larger tire

 

Previous Tundra with 3/1 and 295's on Method 18x9's