What have you done to your 1st gen Tundra today?

You know I'm the paint nazi around here. Don't wait until you lose your clear coat!

 

Vanta black!

 

That’s be a really dark truck

 

The darkest! I tried to get the guys at work to do a trailer with it. They didn't get what I was asking for haha.

 

Just added new HID’s to the front and the fog lights. Lifting and leveling today.

Here you go! Wasn’t too hard. Crutchfield makes it easy! Just takes time and patience.

 

Sorry bud. I posted those pics thinking you had responded to my other post. Here’s the after lift/level shot, before and after. New shoes going on Sunday! Will post those pics too.

 

Good time to put the PHM touch on them belts !

​

 

If I lose the clear I'll bed liner that roof.

 

Picking up mine from its detail and paint correction with ceramic coating in a few minutes. Black is back!

 

Started on driver seat work and hoping to find an upholster 1 county over. Went to our newly opened Raceway Pick-a-Part this am and even tho they had a TRD limited with same oak color, they were only slightly better than mine. He did have other parts that caught my eye for a return trip. Removed and replaced wiring harness after rewrapping with new elec tape and blew all the cob webs/junk out. Will apply temp pwr to it in the am and bench test. Then remove and replace old grease. Can't decide whether to use white lithium or Mobil synthetic ?

 

Got a problem. The video feed is blinking on and off when I put the truck in reverse. I rechecked my grounds and they’re good but I don’t feel great about the power source for the mirror (not the reverse power source).
Anyone know a good acc power wire to tap into in the kick panel (2006 )?

 

I need the little pocket right below the ashtray, the black piece. I'll gladly pay you for it if you could/would grab it and ship to me. How's the steering wheel in it?

 

Would you be willing to share how much they wanted for a seat? I really have the itch for leather. If I could find limited seats that need new seat bottoms for less than clazzios I'd have a hard time not doing it.

 

How’s the bass? I wonder if it’ll fit under my seat.

 

If you have center console like mine, don't think I can help ya. This was a 2004 TRD AC Limited. It's console stopped at front of seats. As far as Steering wheel, there was not one in place, in fact the whole steering column was not in place. I can look thru it for the steering wheel. Be glad to check other things for when I go back next week since I feel I need to go back soon before they trash it up more. They had passenger door and it's shell removed, all laying in front/back of vehicle. Back seat was removed and parts of it were in bed of truck with other crap....underneath frame and engine gone.

 

Making sure I understand....their leather for driver side was not much better than what mine are showing in my above post. If however you're wanting decent seat cushion foam with frame, I'll be glad to find out. Keep in mind in case you didn't know, it's like mine above....lumbar, auto adjust everything....which you probably know way better than me being I'm a newb at this stuff. Would also have to check if it had seat heaters if you wanted that.

If you're just wanting a price of what this pick-a-part is asking, just called Raceway and Wade said $45.00 a seat.

 

I’m still trying to locate some access cab limited seats from
An 05 or 06. Not sure if double cab ones will fit

 

The only Tundra he has is this 2004 but when I go back I can sure ask if/when he might get 05/06.

 

Where are you located? Just curious if
You do happen across some

 

My goal is to find a set of seats and the floor harness for said seats. My dash harness is all wired up for the power seats. The floor harness is not. Would make my life way easier to make it all plug and play. Then just remove the rear half of the harness. Because reg cab life

 

within half mile where TENN/MS/ALA intersect.

Hmmm....I might could help on harness if you could give an idea of how much trouble the floor harnesses would be....after removing seats, remove door seal, throw carpet back and ?

When you say seats....it's like mine, the passenger is manual but does have heat, driver is auto.

 

Hmm a not toooo far from me I guess. Shipping probably isn’t horrible

 

Yes like that. Floor harness is a little involved. But pretty much pull carpet and seats and it’s all there. That’s something I might be able to find locally. I just always miss the seats before I get there

 

It fits great in my pocket back there. And it sounds really good. Sounds like a rich Bose sound vs a truck with 3 12” subs in it. If you want that kind of bass, this isn’t the one. I still haven’t fastened it down. Have to drill thru the floor pan for that and I’m not comfy yet doing that. I just put towels under it and next to the hole metal to keep it from vibrating.

 

How do you do the soak? Do you uninstall them or just extend them fully and clamp them off from retracting? Those belts drive me crazy! Thanks for the tip.

 

Yes like thqt

im after a little more low, but quick response. I’m not a basshole. Just want fuller sound

 

This will do it for you then. The external level control is nice too. You can adjust on the fly. I’m a rookie with subs and haven’t messed with the gain knobs on it or anything yet. I’m probably scratching the surface of what it’s capable of.

 

@Professional Hand Model will hopefully be by shortly with his lilly white hands but until then, the below post is another he made covering just that.

What have you done to your 1st gen Tundra today?

 

I’m shutting it down for the night. My power connection, heck all of the connections are good and are right but my reverse display blinks on and off constantly. I’ll play with it tomorrow but I’m thinking the camera or the mirror is defective...

If anyone has experienced this please let me know.

 

If you have a volt ohm meter, unhook reverse wire connection you made and check that the voltage is solid and not pulsating when in reverse. Chance you got close and somehow shorted or caused a nick to exist between backup lights and blinker circuit ?