What have you done to your 1st gen Tundra today?

I was missing the one so I took the other one off I think I’m going to put on just some LED pods my dad gave me in place of fogs

 

My 03 Limited AC has em as well.

 

One of my 90 day old fog light LED's has quit working.

I think I'm done with LEDs on the outside.

 

You just gave Bubbles ammo. Please stop. Hahaha

What fog led did you use? Didn’t realize you changed them. Think I was in Brasil?

 

Drove a blind person around all day today. If you didn’t know, most of the blind have an extremely good sense of hearing. Her first comment on the truck was how nice my passenger side paint job looks! Hahahaha. That was a joke.

Seriously, we were sitting at stop light about 5 minutes in and she said, ‘This truck is so quiet compared to any other car I’ve been in’. She heard me smile.

 

They are fanless Beamtech's. Installed 9/25..

 

How was the light?

Warranty?

 

Got my black interior paint to try out....
See how it does with the old door panel

 

What paint for you to with? I actually might not mind some more black inside my truck.

 

SEM landau black.

 

Do please keep us posted.

 

Finished the fobby jobby. Its fit and finish is well done, easy to assemble. It’s a nice hand accessory.

 

Just got
The one apart. See if I have time later to paint it

the insert is going to come
From the other door once it have it redone

 

I didn't have anyluck the Beamtech LED's either.
I have a set of their LED headlights but I ended up removing them. My battery would end up dead after several days of sitting while they were installed. Once removed, I had zero battery issues. Never figured it out. I'll give them another shot once I get some new light housings.

 

Installed a Kicker powered sub in the back passenger stowaway compartment. Truck go boom boom boom now.

 

I just verified, I cut the green because my head unit has guidelines available and I can adjust the lines for my preference. I cut the purple for the orientation of the camera. I really like the view that location gives me. Due to the slope of my shell, I just miss the edge of the bumper a a couple of inches. I haven’t towed anything, but depending on your hitch setup I think you would be able to see the hitch ball.

 

Test piece is drying.

 

Hmm. Apparently the bed has managed to come loose in the rear corner.




Back to the body shop to check the frame again. Oh well. The things you deal with once you start driving a rollover truck.

 

Curious to see how that dries. I'd almost call it too black as is in the photo. A cab full of that would be a black hole in my eye.

 

My truck go boom boom boom.
https://youtu.be/mXLRy1cNMWs
Could easily be re-written for a perfect match.
Not going to get that out of my head now....

 

I’m loving the black accents in my truck. I over did the red, but thats an easy fix.

 

I don't really like colors too much inside my vehicles unless it's the same as the exterior, but that black is where it's at. I'm thinking with my black steering wheel cover (via slowboat express eta mid Jan) ,and some strategic black like yours, I might really update my interior. Not to mention one of these days I'll probably have black seats. Either clazzio or black spacer mesh I'm thinking.

 

It’s amazing on how much the color change makes in person.

My next move is to tone down the red and paint the dome and map lights, as well as the center console (lid only). I’ll be using Autozoned Acrylic Lacquer black this time.

 

I must have missed it. Did you spray paint all those pieces black?

 

Yes sir. Used the bed liner spray. As one is never sure until the final product is complete, I will be tweaking some items. My final finish will be Acrylic Black over the bed liner’d areas. I’ll tone down and leave some red accents. Here are a few other pics.

 

When you did this job, did you just lift up a few places and re-stick with Fuze? I thinking about pulling mine completely off, cleaning that channel underneath, painting the weatherstripping, and then putting back in place. I just had more fuze and bedliner spray delivered.

Thinking spray paint is better for this job than the bedliner spray since the rubber will have to bend. Thoughts?

 

Looks great! I like the black updates, with just a touch of red. Nice work!

 

For the exterior window trim I taped it off. No Fuze. That channel is hard to reach, but can be done when the interior stuff is pulled.

For the interior trim, I disassembled the entire works.

 

No sorry, I'm talking about the roof drip molding. I think that's what you had pictured that I quoted from earlier this year.

 

Ok. I thought the quote seemed familiar, but was perplexed as I didn’t read or see my own pic until now.

I sprayed regular enamel over those. Yes, I used Fuze. Lift and clean. Apply dabs of strategic Fuze. Tape off, do clean beads of Fuze, and spray paint in that order.

Acts as a sound proofer as well.