What have you done to your 2.5 gen Tundra today?

Damn - that looks great. Big congrats. I’d trade my 19 sport for a pro.

 

Added this s&b cia a couple weeks ago. So far pretty satisfied.

 

They are the ones posted at the bottom of the thread, from Amazon, $13.95. Amazon has several sellers, these were Sirius LED.

 

It is for both items.

 

Can’t remember where I saw the original post but took the idea and ran with it. Installed some 4” grip tape that I picked up from a local marine shop as my door edge guards. The original owner was 5’ even and it showed signs of how short he was as the drivers door sill was worn down to raw steel from him sliding out all the time. Gave it a quick paint touch up and then applied these on. Most guys use 3” but I figured I’d try the 4” to wrap over the lower seam as well. Neighbors thought I was nuts using my wife’s hair dryer to heat the door sills and grip tape as my heat gun coughed. Ran the hair dryer full blast while I worked the tape all the way down. Using a throw away customer card came in handy. Worked out pretty well I’d say!

 

I recently put some 2 inch grip tape on my running boards and that plastic door sill. Just did the back 2 doors for my daughter to get in and out without slipping. It really works well and looks fine IMO

 

New rock rail step lights.

 

OK..what steps are those?

 

Just returned from 12 volts, 510 miles, roundtrip, and worth every inch!! James installed complete system, head unit, 2 subs, all new speakers, new amp, remote starter, and alarm. This is the best sound ive ever owned. James and his crew went beyond my expectations. Fast, clean service, great people. I HIGHLY recommend him and his staff. Thank you James and crew

 

Vent rings and climate knobs from ajt, then decided there wasn't enough blue on my truck.

 

Updated from the kicker Hideaway to a separate amp and 2 kicker 10’s....think I’m done with audio mods!

 

Nikki, where did you get the rings around the climate knobs? I didn't see them on AJT's website.

 

gave all 3 cars a good washing. I'm amazed with how much beading is still there after the last application of beadmaker.....about 6 weeks ago.
used: Griots wheel cleaner (first time....meh)
wise guy tire cleaner
power washer rinse
foam cannon with CG wash/wax (purple stuff)
rub down with a foam pad
power washer rinse
griots PFM towel dry
ps beadmaker
meguires endurance tire gel (i need more waxaddict. didn't like the gel)

 

im too tired to go take a picture of the truck....here's the RC

 

Fair enough. The car looks great.

 

I just painted them while i had the knobs out. There's small plastic rings on the other side of those chrome ones, you just have to pop them out, then the chrome rings are held in by tiny clips.

 

E
P
I
C

Need a fireball for a lightbar!

 

Came on a set?!?!? Link?

 

Noice!
Giving me some ideas...…

 

Got my wheels Wednesday. I was a bit apprehensive about installing the bronze on MGM,but am super happy with how it turned out. Think it will look even better when all the chrome goes away.

 

Installed Air Lift bags just for my trip this week. Ill be close to max payload I think with all my gear, boat and jet ski. My buddy took them off his Tundra because they almost ride on the internal bumps at ride height with the minimum PSI. Its terrible, they bottom out on the smallest bump. But when you are loaded with 30 or 40 PSI its fine. They are easy bolt on, so it was worth it to me to just install them for one trip that I think I will be heavy.

But if you're looking to buy air bags, don't buy Air Lift.

 

Returned from a stop in Tahoe to see some friends on my way back from Yosemite this weekend. Odometer went from 600 miles to over 2000 in a few days haha. Great road trip vehicle. I hated paying for gas in California, but loved having everything I needed within the footprint of the truck. It's a nice feeling having nothing dangling from the receiver or bolted to the roof.

 

Finally installed these BORA 1.25" spacers, and got them all retorqued and whatnot after driving.