What have you done to your 2.5 gen Tundra today?

So I finally got my 12” shallow mounts installed on the factory HU. It was quite a pain in the ass but it sounds fucking amazing!

Also I washed her today only to come home, and in an attempt to miss a pothole in my driveway, I ran right into a muddy rut and dirtied my baby all over again.

 

Installed bed rail bars and still have full function of the tonneau cover.

 

What do you use those bed rails for?

 

What are you looking for?

 

Went from 35 12.5 20 to 38 13.5 20
Before


After

 

DAYUMMMM. That's gorgeous!!! You have a BMC correct? What brand did you go with? What's your lift?

 

Thank you I'm loving it! Yea have the BMC and even that's close been flexing it and trimming different things for the last hr or so think I finally got it. There toyo mt with 7" BDS

 

Jumped the gun and should have searched for your build Battle. Looks gorgeous, I need to step up, this looks amazing! One day. LOL

 

I got them on. I am so pleased with the look! Stock suspension, K02 275 70 18.

 

Your not the only one that has jumped the gun I just replaced my exhaust for the third time and only put my 35s on 4k ish miles ago already went bigger lol

 

Cm or db? Says it doesn't fit my cm

 

Installed the Alpine PSU-300TND

Also painted the blinding chrome around the cup holders

 

Sorry, it didn't come through. You said you installed the Entune screen protector.

 

What are you doing for your rear?

 

I purchased the matching ADD Stealth Fighter rear bumper.

ADD company photo ...

 

What's that have on it for tires 40s lol makes mine look small

 

Picked truck up from fab shop, Total Chaos Long travel.

 

I got mine from eBay, sorry no link.

 

Thanks bro! It’s a dune flag I grabbed off ebay.

 

I've always liked the look of them and they have function for my Thule crossroads rack system. I ordered the new Thule 78" Pro bars that will allow me to use my bike racks and/or cargo box. This truck will be a primary road trip vehicle for the family trips. I'll post a picture this week when the pro bars arrive.

 

Just slapped on some sumosprings with 2" spacers this morning, in between cups of coffee.

 

Installed towing mirrors from 1AAUTO.

 

I had the Airaid tube on my 6.2 Sierra and loved the sound plus the ability to use stock air box. I actually noticed much better top end with it too. This is probably the only “intake” I would consider simply to be able to swap to a smooth tube to increase laminar flow. Curious if you noticed any improvement by adding the AFE setup?

 

I have 7” BDS as well. 37s, 20” fuel rims, 01mm offset. Still have stock front bumper like you - had to shim it about an inch & light trimming of the plastic (didn’t have to cut any metal on bumper). Still have to do BMC.

For your 38s, did you have to chop a lot of the bumper? It doesn’t look like it from your pics. I assume you shimmed it? If you didn’t have to chop a lot I may get 38s for my next set.

 

I've got the plastics pushed forward a couple inches plus I had to trim an inch or so. No shim. Definitely needed BMC and still need to hit the pinch welds a bit further up than i have gone so far. I thought i had it but went over some healthy ruts at full turn and it needs a little more

 

Here’s some pics of my install for my amp and subs. Sorry I didn’t take picks throughout the process but here are some of the finished product. I installed the PAC SNI-35 under the passenger side door sill plate. Hooked it up to both rear speakers and ran 6’ RCAs to the amp.
I decided to install the fuse holder under the driver side door sill plate as well. All in all it’s a pretty clean setup. I’m happy with it and it sounds great.

 

Started the 3M tailgate insert mod...makes such a huge difference from the previous ones installed. Great cheap mod!

 

Spray painted the front tow hook.