Official Tundra Wheel and Tire Setups - Pics and Info

Any rubbing with this setup?

 

I love your setup, what's the specs on your wheels?

 

18 x 9 Methods, 295/70/18 Nitto Ridge Grappler, Bilstein 5100 on top setting. No rubbing, great ride..

 

Ray 10s

 

Only rubs a little bit in reverse at full lock, going to trim up the front plastics a little bit when I get the time.

Separate note. The Atturo trail blade XT’s sucked and would not balance out, so I replaced them with
Mickey Thompson Baja Boss 295 55R20
Will post pic soon

 

Thanks for the reply. I’m looking at the Toyo open country rt.

 

Toyo’s are nice, had a set of open country at’s. They weren’t very aggressive looking but they ride really nice

 

The rt is between the at and mt. Supposed to be the best of both worlds. Just don’t know if the 305/55 would rub.

 

Ok so I took off the mud flaps and the front little flap things and it only rubs a little in revers on the front bumper plastics if I would have gotten say a positive 12 offset instead of the 0 offset on my rims it might have cleared but not sure if it would rub on the back side. When I switched to the mickeys I went down to a 295 and it still hits a bit in the same way. It’s not bad but I do need to trim my plastics. But I do not have any body mount issues, which I hear can happen with some setups

 

Oh ok gotcha. Thanks for your help. I’m looking at a +20 offset

 

Looks great my man. Damn where u been lately, you've even been more MIA than me lol. Hope all is well.

 

Tnx brother...being on here cost me money

 

I know the feeling. I've been staying away a bit lately knowing I can't buy truck parts at the moment lol. Good to see u still around.

 

Just installed! Didn’t even have time for a bath yet. LT285/75/18 Goodyear Duratrack‘s on Raceline Defenders 18x9” +18mm. Removed factory front mud flaps and tuck up front bumper fender liners a bit…no rub on the way home. Should still have room for tire chains.

Next up……Flares!











Update:
Just got back from a trip into the Idaho back country and WOW! What a difference in smoothness and ride quality these new meats make vs my old 275/65/20 ‘s. Over 100 miles on rough gravel roads and it’s clear…there’s no comparison for ride quality between 18” and 20” wheels. So glad I ditched the 20” city-slicker setup.

 

20s fuel sledge
35s nitto mud grapplers
-18 offset

 

Ok so I’ve searched and I can’t seem to get a definitive answer. I have bilsteins and it’s leveled(ish). I haven’t crawled under and checked what notch but it sits fairly level. I have method standards and I’m ASSUMING (based off their website) that it is -12 offset/4.5” backspacing. Found a killer deal on 34x12.5x18 km2. I want to pounce but don’t want to have to find out they won’t work. I’m fine doing a cmc and hacking up some fender trim. Will they work with the wheel set up?

 

That’s a lot of offset. I just put on +18mm wheels and 285/75/18 tires (35.1” x 11.2”) and I’ve got maybe 3/4”-1” between the tire and body mount.

It’s not a 1:1 addition at the corner of the tire , but your -12mm wheels will kick out the sidewall 1.18” inches over my +18’s. Add in the extra 0.65”, and that’s a considerable bit of distance toward the body and fender, 1.83”.

I used this website: , to help me compare my current to my possible future combinations to make sure they would fit.

Without someone who can actually confirm that combo for you it’s a bit of a gamble, unless you can somehow mock-up or project from your current to desired combo and test it out.
Best of luck!

 

I’m mistaken, they are 18/5.75
Method 301 “ standards”

 

I bet you’d be fine then.

 

Good to know. $150 for all 4 tires and they look like 75% life still

 

What would be the issue or point of contact? The UCA or the body mount?

 

I’ve got plenty of room at the UCA ball joint. The closest points for me are the fender linings in front of the tires (already pulled them forward a bit too) and the body mounts.

 

So did you get them? Let’s see some pictures and hear how they fit if you did.

 

I didn’t. Thinking they are a bit aggressive for my taste . If they are around next weekend I may just do it but for now, looking for another 35 in a less aggressive pattern

 

20" KMC Slides -38 offset
285/65/20
BFG A/T

 

Think those are +38 offset

 

Yes sorry, +38

 

Good looking truck

 

Anybody know tire size options for a 2011 rock warrior wheel and 1.25 tire spacer and possible 2.5/1 lift? Plan on BFG AT