Connecting Aftermarket Fog Lights

Hey, I’ve got four of these fog lights and I don’t know how to connect them. My truck is wired for fog lights, I just need the connector for these wires. Where can I find them?

 

To run those your going to have to clip off the stock connector and hard wire them accordingly. Red to red and black to black. If your not okay with that you will have to get yourself the opposing female connector and wire it onto the fog light's leads. Easier if you just snip those wires and wire them together with your choice of crimp on connectors from your local auto parts store.

 

Thanks. I’ll probably clip them since it’s not like I’m going to run anything else in the future.

 

Do yourself a favor and get something like this.
https://www.walmart.com/ip/2-Wire-W...edirectid=15632259510026535925610080302008005

 

https://www.ebay.com/itm/2x-New-900...sal-Pre-wired-Connector-Pigtail-/233196067622

 

I would also suggest not cutting the factory harness, spend the few bucks get the adapters as shown

 

So how should I connect 4 lights to the 2 OEM connectors?

 

Just tie the lights together, it isnt perfect but it is better than cutting the factory harness. I did this with the 4 lights in my DV8 bumper on my 2nd gen, works fine. LEDs dont draw much power at all.

 

Tie 2 fog lights on 1 side together and the other 2 on the other side then get yourself these listed below, wire them to the fog lights, 1 on each side, they plug into the stock fog light harness. Don't cut the stock wiring, save you issues later on.


Check this out at Amazon.com HALOYiVGO H8/H9/H11/881/H27/880 Bulbs Male Connector Sockets Adapter For Headlights Fog Lights Retrofit Extension Wiring Harness ABS + Copper Wire 2pcs (H11)

HALOYiVGO H8/H9/H11/881/H27/880 Bulbs Male Connector Sockets Adapter For Headlights Fog Lights Retrofit Extension Wiring Harness ABS + Copper Wire 2pcs (H11)

https://www.amazon.com/dp/B07HF6PMQX/ref=cm_sw_r_other_apa_i_a4qlDbMZ66RKF

 

That's an H11 female plug. You just need to wire male H11 to the light and plug them in. You can use heat shrink tubing over the H11 connection for further protection.

$8 iJDMTOY H11 H8 880 881 Male Adapter Wiring Harness Sockets Wire Compatible with Automtive Driving Light, Running/DRL, Fog Light, Retrofit, Off-Road Lighting, etc

https://www.amazon.com/gp/product/B01HNAT6CW/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

 

Crap! glad you caught that, posted wrong one going through my Amazon orders

 

Thank you guys. I’ll post the results.

 

Bought these but they don’t fit the harness on my truck. Any ideas?

 

Hmm... I've used those on my fogs on my last 2 tundras. On some of the H11 plugs the locking tab might interfere and need to be removed.

 

Use these then, you can tap your harness and unplug them if needed. Did it on my old jeep. Can get then at the auto store

Check this out at Amazon.com Nilight 120 Pcs/60 Pairs Quick Splice Wire Terminals T-Tap Self-stripping with Nylon Fully Insulated Male Quick Disconnects Kit, 2 Years Warranty

$9 Nilight - 50004R 120 Pcs/60 Pairs Quick Splice Wire Terminals T-Tap Self-stripping with Nylon Fully Insulated Male Quick Disconnects Kit, 2 Years Warranty

https://www.amazon.com/dp/B07CP987BN/ref=cm_sw_r_other_apa_i_xV5mDbDZEKTZB

 

Thanks guys

 

They make adapters with 2 fog light connections.

 

Question
Can I just replace my stock fog light bulbs with LED’s?

 

Dredging this thread up in my search for an answer. Please bear w me in that I'm not very electrically inclined and have been trying to determine what type of connector I need to use to connect these ends w an adapter pigtail.

These are the two female connector ends...finally got around to getting pics of them....C19 and my MH clinic have kept me crazy busy...

This is the female connector on the ARB fog light side.


Tundra fog light connector.


Ideally, I'd like to have a pigtail adapter that goes betwixt the two without cutting...where can I find this?

Thanks!

 

No worries on bumping. Might have better luck starting your own thread as well. Sorry I can’t help more