Chrome Delete Covers for Tundra Bumpers - BumperShellz

Seeing some posts about breaking those fender clips, so I looked into it. If you pop a trim tool in there, it will unseat the undercut section around the screw hole which will make it much less likely that the clip will break. I'll put a hint in future instructions to help minimize how many of you that happens to.

 

Loving this flood of Inferno!

 

EC1 - Any update on the custom color Black fronts? No tracking info yet.

 

Do you need to remove and reinstall front sensors for covers?

 

Yes, but it was no big deal. Unplug them, put on cover, then fish them back through and plug them back in. There is a bracket that holds them in place, so there is really no way for them to get out of alignment.

 

Yahoo my front covers showed up today...but it will be a week or so before i will have time to put them on

 

What color did you order?

 

Just watched an install video...

SHOULD NOT HAVE DONE THAT.

Now I am absolutely itching to get these.

Would love to get confirmation that the Cements got shipped out and/or will arrive next week....?

I'd like to believe I was one of the very first to order seeing as I was sitting here refreshing the page constantly until @EC1 said "go"

 

That's good as long as you get the bolts to tighten then you ok you can always replace the brackets in the future

 

Install was easy its just I didn't know the bracket and liner were connected when I pulled mine right off...but again that only happened because I removed the liner to put new end caps or else your install doesnt require to remove the liner unless maybe u have the sensors

 

I'm sure there would be another buy coming soon

 

Any update on the TPO front and rears with no sensors? My patience is wearing thin!

 

Where did you see an install video?

 

For Non-Sensor Cover installs .... https://www.youtube.com/watch?v=SNFawLY71HE&list=PLZwRjXq5VCe9rkseeglLjBW0sL1I4Lrm2&index=2&t=0s

 

These are the sparks ones but it’s pretty similar I’m guessing...

 

I really wanted to color match but was afraid the colors would not match as well. Also, there wasn't enough interest in an inferno paint run anyway.

 

what page to find pricing and order instructions. can i order on non group buy?

 

Contact @EC1 he will tell you how to buy and as far as pricing goes it's on a few of the pages on the threads the only thing is looking for it in these many threads

 

From EC1: "We're going to take about a week after we get all of these orders out to re-stock and take naps lol. After that, we're going to release them to the public. I'll post on this thread when we release them. Just sub to this thread to make sure you don't miss it."

 

page 1 has order info, tried to order tpo, out of stock came up. w/out senser holes 124.00. sparkparts wants over 500.00 for front and rears and can only order front and rears. i just need the rears.

 

@EC1 , any update on the super white being shipped?

 

For the front covers, did everyone reuse the screws or get longer ones? Longer ones do not come with kit, correct?

 

I'll let you know in a couple hours. Only an hour left at work, then I'm heading back home to install my fronts.

 

Reused with no problems!

 

Take some pics of the install and any advise, please. Thanks

 

I used same screws they are fine as long as the nut on the bracket does not strip then u can still reuse it

 

Did anyone else seem to find one of the bolts on the bottom of the inner fender didn't want to go back in all the way. It felt right, but the washers were still flopping around so it wasn't all the way in. I tightened it just til the washers didn't move any. Want to make sure I didn't over tighten or put too much stress on the bumper cover. I'll post a picture of the Bolt in a bit, I just ran up to pick up dinner right now. Also, for anyone that hasn't installed their covers yet follow @EC1 's tip about using a pry tool on the clips, it worked like a charm and none of mine broke.

 

You might of stripped the nut on the bracket I did the same thing so had to purchase a new bracket they cost around $13-$17 depending dong on the style

 

Are you referring to the bracket that people mentioned above where the clips broke? The one I'm referring to is a larger 12mm bolt on the very bottom (only reason it is removed is to take out the plastic inner fender to access the back of the sensor that needs to be unplugged).