2019 Tundra CM Eibach 3/1.5

All,
I am new to the forum and wanted to run my plans for my 2019 Tundra 4X4 CM by you guys for your input. I was planning on the Toytec Eibach 3 inch coilover kit with the Toytec adjustable shackle in the rear set at 1.5 inches. Method NV 18X9 with +25 offset on 295/70/18 Toyo at2 extremes or Cooper Maxx. SPC UCA's. I'm trying to avoid doing a BMC but if I have to I have to. Any input, comments or concerns would be greatly appreciated. Thanks!!!!
Tad

 

I run the Toytech Eibach in front and CB +2 shackles in rear on my 17 CM. I also run +25 SCS SR8's with 295/70/18 Cooper Maxx tires. TC UCA's . I did not need to do a BMC. I did add the CB bumper shims to avoid and trimming in the front. You should be good to go with that setup.

-Mike

 

Thanks @Scud!!!

 

@Toytec Lifts

 

Well this arrived today!!!! Thank you @Toytec Lifts. Unfortunately the shim I ordered to put on the driver side coilover does not line up with the studs. I have tried every which way and it’s off by 1/8 of an inch.

 

What shim is it?

 

@Toytec Lifts Part Number 10714. I’ve tried everything and don’t want to mess up the threads on the coilover.

 

Shoot me a pm with some pictures please

 

Sent @Toytec Lifts . Everything else looks awesome. Solid stuff!!!!!

 

Glad to hear man!

We are on the phone with the machine shop now.... Ill get you more info via PM.

 

@Toytec Lifts is already on it!!! Customer Service seems solid too!!!

 

Has anyone had any issues running 3/1.5 with the 2019 Toyota Safety Sense (TSS)? A local shop lifts their 2019’s with a 3/2 for that reason but said that the 3/1.5 should be ok.

 

SPC UCA’s arrived today!!! 1 more price to the puzzle and it will be install time!!!

 

FYI, there are a few people having issues with the amount of lift that they're getting from the coilovers. I would HIGHLY recommend not installing them and contacting Toytec first. Just trying to save you from a pain in the ass. Apparently Toytec is in contact with Eibach to resolve the issue. Toytec has removed the Eibach Coilovers from their website.

Eibach tested these springs on a 2WD Tundra and not a 4WD, so you'll only get about an inch of lift.

Once you install the coilovers, you can forget about support from Toytec.

 

@CyberViking . My Eibach kit from Toytec arrived 2 weeks ago prior to them pulling the of their website. I have installed it yet. Wounded if they will refund me or send me the Boss coilover instead?

 

They should refund you but my experience with them has not been good so far. I would call them first thing tomorrow.

 

I installed this same set up on my 2018 CM TRD two weeks ago. I have approximately 3 inches of front lift and the 1.5" shackles. I am running Toyo AT II 295/70 18 Extremes and stock UCA's. NO RUBBING AND NO TSS ISSUES! I am in complete front alignment and straight down the road.
I did trim the sides off the belly pan but did not have any other trimming or cutting of the cab mounts or frame what so ever. I did remove those tiny front mud flaps.
PAY ATTENTION WHEN MOUNTING SHACKLES!! Only tighten to 90 ft lbs! If tighter, they will squeak and rub frame. I used my factory top bushings with the new inserts after reading several forums of people complaining about squeaking and have zero issues.
I am running my Toyo's at 43 psi front and 44 psi rear on stock TRD rims, and have found this to be a happy medium for raod noise, handling and comfort.
I have owned many brand trucks and even a 4Runner, all lifted by me. When you take it for alignment, GET AN EXPERIENCED TECH!! Your truck should align fine without the SPC UCA's.....a waste of $600+ IMO. Also, Rock Auto sells the SPC UCA's for like $215 a piece!!!
Rough Country/Hypertech speedo calibrator installed easily for a buck 49.
Couldn't be happier with the ride, comfort and handling of my truck with Toytec/Eibach 3/1.5 kit!! I already put nearly 2000 miles on it and NO ISSUES! And this is the third Tundra I have done. Hope this helps.

 

How was the hypertech install? I’m just hesitant to take the dash apart.

 

LT75 - simple install. Easier if you have small hands. All you need is a screwdriver and an 8 and 10mm. Don't forget to disconnect battery!

 

Thank you for the great information @Losanjo !!! I’m just hesitant now with installing the Eibach kit with all the issues that keep popping up with it. Also, I was planning on seeing how the truck aligned with the stock UCA’s and can always return the SPC’s if needed. Thanks again!!!

 

Call toytec and return the eibach/toytec coils. Then, call Darren at boss4x4 and order 6112s. Trust me.

 

Show us some hub to fender pictures just to give others peace of mind

 

Hub to fender as requested...

 

You got 2.5”? UCA’s aren’t really needed till you get around 3”+

 

Is that driver or passenger?

 

I got right at 3". I was around 21.5" stock. It's the passenger side, but I sit even. And....I don't have aftermarket UCA's??

 

Glad to hear the Eibach kit worked for you @Losanjo . I decided to swap the Eibach Coilovers with the Boss Coilovers with the recent issues going on. I feel the 700 spring and the adjustability will be a better option for me. Toytec was very helpful in the process!!

 

I’ve been on the hunt and out of 6- 18’s tundras not one was 21.5 fender. They all were 22”. Can you send a pic of your coil perch were its set on what setting?

 

Stock height on my 2019 CM 4x4 is 21.75 inches on both sides. That was from the center of the hub to bottom of the finder.