Ultimate OEM Toyota Parts Thread for 2nd gens (2007-21)

Any write ups or diagrams on swapping out front bumper ends?

 

Do you have links to center console wireless phone charger and LED bed lights? Can't find them.

 

Hi Roman, I've tried to read through the whole thead, but it's getting quite long.. I've gotten blackout replacement badges for my2018 Inferno SR5, but unfortunately where my wife picked them up she was unable to get me blacked out SR5 badges. Are these available? I would prefer to get factory replacement badges rather than the overlays.

 

Will the power fold tow mirrors fit a 2007? I have heat and power and power fold already (not sure if origins or If previous modded)

Up to what year if I get a newer truck and want to move them over?

 

If you currently have Heated and power adjustable plus power fold Mirrors on the 2007 you can use the tow mirrors from 2007 to 2011 for sure because I took a set from a wrecked 2011 and put them on my Limited 2007 when I had it and been told up to 2014 that I am not positive about, First thing to do is look and see what style electrical connector the current mirrors have to make sure that they match.

You can Check to see what your Truck original Equipment is by going to the Toyota Website and Entering your Vin Number here - https://www.toyota.com/owners/ and select "My Vehicle" then "Vehicle Specs"

 

Thanks, didn’t know you could do that. it just says power mirrors and cold kit so I assume that gets the power adjust but not power fold mirrors with heat?

 

Power Mirrors with Cold Kit from Toyota = the mirrors are electrically adjustable and they have the defrost (heat) and the Switch will NOT have the little square button to the right of the left and right selector button like the picture shows. However both Types of Mirrors will fit so if you do not have the Fold option on the Truck you can add it with purchase of the proper switch, Plugs and possibly need a relay plus some wiring work.

I know somewhere among all the Forums here there is a full write up on how to do it with list of what is needed and I guess now after all this I am going to go look it up because my current Tundra has the Tow mirrors but they do not have the Power Fold and I remember how good that was to have..... oh here we go

 

https://www.tundras.com/threads/how-to-remove-front-and-rear-bumper-caps-2017-and-reinstall.9858/

 

Thanks. I do have the button and the fold option does work today on the standard mirrors.

 

Then with the Correct Tow mirrors you are all set the Toyota OEM ones are a bit pricey you might luck out and find a good used set of OEM ones as for the after market ones I would ask around here and see what others who have made the purchase have to say because I have heard both good and bad about after market ones and I am not familiar with the brands that are good.

 

@Roman do you have a part number for this plastic piece with clips that mounts to the fender liner behind the bumper ? 2018 crew max
The clips broke off

 

I think he's out for vacation for a few more days. Pretty sure he listed these in Post # 1 under the bumper end cap section.
https://www.tundras.com/threads/ultimate-oem-toyota-parts-thread.10707/
..listed as the "seals you will need"
these are for the plastic end caps, not the chrome ones. I'm pretty sure the chrome end caps have a different seal & part number.

Hope that helps, otherwise you can wait for Roman to get back from vacation.

 

I’ll take another look at the beginning of the posts but I do have chrome caps. Thanks

 

I -think- this is correct...
these are for the plastic caps: 53882-0C060 and 53883-0C050
these are for the chrome caps: 53882-0C050 and 53883-0C040

But I have also seen information that indicates the differences are whether or not you have the off-road package on your truck, so I'm not 100% sure
@Roman can confirm which ones are correct, and maybe can tell us what the difference actually is (chrome vs plastic ; or off-road package vs not)

 

It says on the cool springs parts website with off-road package or without off road package. So I think you’re right about that. It’s hard to tell by the diagram but I think you pointed me to the right part. I’ll wait for Roman to verify. I’m not in a rush. I rigged it up pretty good it will hold for now.

Edit. I found post 584 where someone was looking for the same part. @Roman specified that “those are the ones for the painted end caps” so just need to figure out which is for chrome (if it matters). Doesn’t look like it matters to me. It don’t say anywhere in the item description for chrome or not.
Roman said disregard the “off-road package” apparently it don’t matter

 

@Roman
If I want the 18+ Platinum grille on my 16 Platinum, do I still need to purchase the bulge? Sorry if this question has already been answered.

 

The hood bulges are the same aside from colors. If you don't want to change the color of the one you have then you only need to purchase the grille.

 

I don't see why not, but does anyone know if these will fit in my 2016 SR5 fog light housings?

I want to make sure I'm not missing something. This seems like a quick upgrade.

 

@Roman or anyone else here know the part number for this clip on the taillight? Mine broke while removing my tail light :/

 

Ya'll are going to make me go poor with these mods LOL

 

Welcome to the forum. Hope you like ramen.

 

I just installed these on mine, they should work - they're accessory knockoffs to the OEM LED lights but much cheaper. So far working great.

 

@Roman hit me up when you get back from vacation please. I want to get this hose ordered from you.

thank you sir!

 

Hey bud,

Toyota only sells that little hose with the radiator hose itself.

https://parts.toyotaofcoolsprings.com/oem-parts/toyota-upper-hose-165710v020

 

Ordered. Thanks Roman!

 

Wondering the same, mine broke as well...if you have any luck please let me know, thanks in advance!

 

The part # is on the clip itself

 

Install on my 2019 no problems just plug play @Roman has blue clips to help support housing because it’s a little heavier than stock ones. I went with the zip tie route to make mine more sturdy.

 

Door Sill Protectors for 2nd gen regular cab long door?

 

@Roman shipping price discrepancy mobile browser vs. PC.