1. Welcome to Tundras.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tundra discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Tundra owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

K&N CAI new install

Discussion in 'Performance and Tuning' started by 040Tundra, Nov 18, 2016.

  1. Nov 18, 2016 at 3:08 PM
    #1
    040Tundra

    040Tundra [OP] Teddy 2013-2019

    Joined:
    Nov 13, 2016
    Member:
    #5188
    Messages:
    3,809
    Gender:
    Male
    First Name:
    Aaron
    Las Vegas, NV
    Vehicle:
    040 '16 CM LTD 4x4
    A little of this and a little of that.
    I have a 2016 Tundra Limited with a Mangnaflow exhaust and just installed a K&N CAI today. Is there special driving that needs to happen to reset the onboard computer before putting my foot down or can I drive aggressive right out of the shoot? Thanks for your replies....
     
    Last edited: Nov 18, 2016
  2. Nov 18, 2016 at 4:08 PM
    #2
    CaptTyler

    CaptTyler Life’s too short to have an ugly boat.

    Joined:
    Jul 23, 2015
    Member:
    #1561
    Messages:
    1,461
    Gender:
    Male
    First Name:
    Tyler
    Florida
    Vehicle:
    2018 Ram 2500 Cummins
    You certainly don't have to but anytime I install something new to my exhaust/intake/computer, I disconnect the battery for an hour or so. That resets the computer and starts from scratch.
    After that you're good to go normally as far as I'm concerned.
     
  3. Nov 18, 2016 at 4:28 PM
    #3
    040Tundra

    040Tundra [OP] Teddy 2013-2019

    Joined:
    Nov 13, 2016
    Member:
    #5188
    Messages:
    3,809
    Gender:
    Male
    First Name:
    Aaron
    Las Vegas, NV
    Vehicle:
    040 '16 CM LTD 4x4
    A little of this and a little of that.
    I disconnected the negative battery terminal before installation and left it off during the entire install. It took about 2 hours to do the install, maybe a little more. After the install, I reconnected the negative cable to the battery. Does that count?
     
  4. Nov 18, 2016 at 4:45 PM
    #4
    joonbug

    joonbug °°°°°°°°°°

    Joined:
    Oct 13, 2015
    Member:
    #1948
    Messages:
    16,674
    Gender:
    Male
    First Name:
    Joon
    NorCal - Dublin
    Vehicle:
    2020 Long Travel DC
  5. Nov 18, 2016 at 4:51 PM
    #5
    040Tundra

    040Tundra [OP] Teddy 2013-2019

    Joined:
    Nov 13, 2016
    Member:
    #5188
    Messages:
    3,809
    Gender:
    Male
    First Name:
    Aaron
    Las Vegas, NV
    Vehicle:
    040 '16 CM LTD 4x4
    A little of this and a little of that.
    Thanks!!!!!!!
     

Products Discussed in

To Top