Can I get away with 295/70/R18’s

Hiya all, I am new to the forums and truck customization in general. I have a 2016 Tundra SR5 with a 2”leveling kit on the front and using 18” stock wheels. Can I get away with 295/70/R18 tires. It’s a 2 inch height and 1 inch width increase. Any help with this would be appreciated. I am not very “modifying savvy”

 

Yes, I'm running a billstien level in the front , stock wheels, stock rear with 295/70/18 nitto ridge grapplers. I did remove the small mud flap from the front of the fender well. No rubbing at full lock out. It's close to the uca but hasn't been an issue

 

Pardon my ignorance but what is a “UCA”. Thank you for the help.

 

Upper control arm

 

Thank you

 

Thanks for the info! I just bought a 2019 and having the dealer install a Ready Lift 3"-2" and bought STT PRO 295/70 for stock wheels. When the tires came yesterday, I looked at them and started thinking there is NO way! All will be installed tomorrow and I will post a pick! TY

 

295/70/18 with 2.5" lift, remove the front mud flaps and i've got an inch of clearance at lock, no rub. MPG shit now

 

Yes MPG sucks but truck I bet looks bad ass

 

Yes, i love it! 35's seems like the right size tire for the Tundra, 33's too small, 37's too big.

 

Thanks guys. I just had my stock wheels done to save a few $$$. Now I just have to put the leveling on the front and get those new skins!

 

Looks good. Here is mine.

 

Looks awesome bro. My wife saw yours and said we should have went Crewmax.

 

What size are your tires?

 

They are my”old” 275’s. I am going to
295/70/18’s when they wear out.

 

Felt the need to throw in another 2nd gen to this thread lol

 

I was going to go with the double, which has ample room, but that crew max has a ton of room! I wanted the double so I could fit my 4wheeler in the back, now I will just get an extender for the bed.

 

Love the TUNDRA graphic. Where did you get it?

 

Even cheeper now but be careful on the quality of the material sun fad and cracking .I would go with 3m at least

 

Thank you

 

Yes you can, I have a two inch spacer in the front coils RevTek leveling kit" and my 295/65 18" do not rub. FYI

 

Np

 

I was looking at 305/70/18 with a 2 inch level kit. Mathematically it seems to work. The 295’s aren’t much smaller. Any ideas or comments.

 

Sorry but don’t understand your mathematical approach. 305/70 wheels are 36.8” in diameter. You will have to do major metal trimming.
Rubbing depends a lot on wheel offset.

 

Yes...I realized after I posted that, I failed at math. I sent with 20 inch rims with 285/60/20's instead. Gotta do some minor plastics trimming tomorrow at the garage.

 

I’ve ran 295s with stock wheels,stock wheels with spacers, 18 offset wheels and 0 offset wheels. 2.5” lift then a 3” lift all had the same rub. Defiantly the best size tire for a 3” and under lift.

 

I’m still rubbing with 2 inch level kit and -25mm offset. I was gonna cut the plastics today but there is metal behind there. Should I just take a rubber mallet and try banging the hell out of it to create some clearance. My stocks were 32.6”. These are 33.1” not much size difference

 

So no issues with 3in lift and 295s on stock TRD OR wheels?

 

i have your exact same set up and i'm hitting the sway bar. I'm on the fence with getting spacers