SCS RAY10 18x9 Group Buy Pre-Order

Where is #5?

 

Be careful and watch very closely when the Tires are Mounted / Balanced & when you get your Alignment.
My Ray-10's were scratched and neither Vendor would take responsibility. They just blamed the other one.

 

I will look at them before installation. Number 5 is in CALI and that’s where it will stay until I need it. Anyone know the torque specs?

 

WOW, that's horrible. They really did a number on that wheel. More than likely, it's from using an iron bar during the tire mounting process. I've never seen wheel damage caused from getting an alignment before.

 

97ft lbs in case anyone else is wondering.

 

I know I was So Pissed...

Quick question... Do you think doing a Ceramic Coating would help protect the Ray-10's or is it a Waste of $$$

 

Ceramic coating helps to protect any finish from fine light scratches. It wouldn't have stopped those kinds of scratches that you posted. Usually, you would want to get the coating done first before tires are put on. It's easier for the coater to do work with and possibly be a little cheaper.

I would only recommend doing it on mint wheels. For the most part, it helps mainly with water beading and providing a thin layer of protection from light scratches.

I would do it on the truck's paint first before I'd do the wheels.

 

The ceramic coating is really there just to protect the finish from break dust inbeading itself in the finish. It will also make it easier to clean. No harsh chemical needed to remove the break dust that build up in the barrel. Some wheel cleaners might fade or might damage finish. Now I can use just a ph balance shampoo to clean with a power washer.

 

Anyone running these with no lift or level? Curious what it looks like.

 

We never do sales., sorry.

 

WOW, that's the one for me. Looks great.

 

Ray10 in 18 with 295/70/18. Lift is OME front coils with OME rear shocks and Toytec shackles.

 

Gold

 

motivate em with a picture..

 

Here is a Pic of mine with the Gunmetal & BFG 34's...

 

Today at my shop. More pics to come to introduce myself. Having some rubbing issues. Thanks.

 

What size are your tires?

 

Tires are LT275/70/18. Falken Wildpeak A/T3W

 

I had rubbing with the same size and wheel (different tire) even after leveling. Had to remove the front guards (small molded pieces at the front of the tire).

 

I have BFG 34's & had rubbing.
I pulled off the small front and rear Mud Flaps and the Rubbing Stopped.

 

I removed the flaps, but rubbing is on the molded plastic attached to bumper.
My 5100s are set to the middle setting. Would moving up to top setting help? How does top setting effect the ride and does it put strain on other parts. Thanks

 

Not sure about the 5100's.
I have the King Adjustables on the Mid Setting & adjusted to almost full Soft.

 

Do you have these wheels with the smaller center bore for the first gun tundra...106mm` are you able to provide specifics on BS? available;able 17x8.5?thx

 

Our Ray10 16x8 4.00" bs and 17x8.5 4.30" bs would fit your 1st gen Tundra.

 

Guys i need help. I seem to have misplaced the lug nut key for my Ray10s. Does anyone know if SCS sells those seperately? Do the Keys fit for all sets of ray10s?

 

SCS lugs are 8 spline. You may be able to find one locally. When I bought mine from SCS I bought an extra key so these should be available individually.

 

Thanks! 8 spline. Do you happen to know the bolt size as well? is it 21mm?

 

Not positive about this.

@SCSPerformance will know for sure.

 

Spare spline keys are available on our website for $10 shipped. M14 is the size you'll need.