General Supercharger Thread.

There's a set of instructions from Toyota for 2007-13, and a slightly different set for 2014+

Ok nevermind I see your update that you also did it lol

 

Thanks for sharing, I wasn’t aware of this difference between the magnuson and Harrop in regards to the TB wiring. Seems like Harrop tried to make it easier with a harness but only introduced a failure point. May have to do this to be proactive instead of having an issue roadside.

 

I just reused the oem tb harness with zip ties to avoid any potential issue. Theres minimal tension on the wiring after a little reroute.

 

Well hell...with the Maggy on, the Stillen intake tube is to long. And the custom tubing would require a rework of my adapter or some absurd offset couplers...

I gotta figure this out quick like. Anyone got a Maggy intake for sale cheap?

 

Would a silicone coupler reducer cover the gap? These are up to 6" long!

https://hpsperformanceproducts.com/...forced-transition-hose?variant=40803544924350

 

It's hard to see from that picture, but the intake tube is offset to the rear of the TB. I'd need two offset couplers, one 4.5" to 4.5", and a 4.5"-3.5". The offset reducing couple is proving hard to find

 

Wow, that's miles off...not sure what your options are, other than modifying that box to change the entry angle.

 

The intake tube that comes with the Harrop is flexible, wonder if that might would work for you? Temp MAF rube replacement until you find a better solution? Top right in this pic

 

That sucks & I'm going to have a similar issue.

 

Maybe. I'm going to think on this till this afternoon. Other option is to order the TRD Intake Tube, if I can verify the Supercharger part number separate from the non s/c TRD intake tube.

https://parts.sparkstoyota.com/p/TR...0300140AC.html?clickSource=relatedPerformance

https://parts.toyota.com/p/Toyota__...-Air-Intake-System/69528501/PTR0300140AB.html

 

You may be able to buy at least the lid off of this guy. He was switching to a non SC lid. https://www.tundras.com/threads/wanted-stock-air-box-lid.120026/

 

The bottom half of the airbox is the same as any 07-13 tundra which can probably be found cheap and easy. I have the magnuson tube and clamps I could send you.

 

I would rework your printed part to accommodate parts as they are available. The other option is to use a duct coupler to route your intake through it and seal it off in similar manner like I did.

When I looked at offset coupler reducers they only dropped in 1/2inch increments and the elbows make them hard to trim down to cover shorter lengths.

A flexible coupler pipe like @armyoffoo is suggesting could work to but the largest size I could find was 4 inches. Spectre #9775

$43 Spectre Performance SPE-9775 4" Flex Boot, Black

https://smile.amazon.com/gp/product/B00553PQCY?ie=UTF8

PM me your addy and I can ship it out to you at no cost.
NOTE it is not recommend for boost applications.

 

Will pm you. I'm thinking I could get away with using the magnuson tube and some couplers. I may have to get the stock lower box back out of storage since it looks like it's outlet is more in a straight line with the TB than the still is.

I gotta go do some work work, though. Monday's UGH

 

Been a while since I have looked at mine but what

That's a pricy piece of rubber!

 

Damn job getting in the way of life!

 

Not a whole lot of flex to this one. I have a longer one off of the Supercharger parts store that is more pliable but longer and it is rated for boost applications.

 

Sounds good. Just be aware the magnuson lid won’t work with the factory 2014+ lower air box. 14+ is a good bit smaller.

 

Same problem here. I should be out doing more data logs but nooo, gotta work

 

I wonder if the boosted rating is in regards to positive pressure, like if used for turbo outlet charge piping. I’d guess it would probably be ok on a SC application where it would be more of a slight vacuum.

 

Not sure but a good point. The Amazon listing states "Not recommended for turbo-charged and super-charged engines". The product box gives no such warnings and only states its for an intake. What I've found is some couplers list their PSI ratings but most don't.

This particular product is pretty stiff so not a lot of flex to it. I have a flex coupler from the SCer parts store you linked that is rated for SCs but it is longer and more flexible. Personally I don't like the ribbed surface, I think it will generate turbulence but I'm not an ME/Aero guy so what the frack do I know. In a pinch to get the project running I think it will be fine while he figures our a permanent solution.

Looking at the small physical envelop and the tight angles I would work from the TB side into the box to figure out a solution. You can redesign your 3D printed part but you can't change the TB angle or dimensions.

 

Anyone know about Magnuson serials & build dates? The SC has a 2017 date but the bag the pump & injectors were in have a '21 date.

 

This is getting ridiculous... here is a Parts/Price list for converting my existing fuel delivery setup (2x6AN pump feeds to Y-block 8AN to engine bay Y-block back to 2x6AN feeds for fuel rails and 2x6AN return to FPR and 6AN return to tank) to a 8AN solution from pumps to FPR.

Prices are totals where Qty greater than 1, not including tax and shipping, void where prohibited, available while supplies last, may cause uncontrollable flatulance...

From XAT:
XAT Racing 3UR Fuel Rails Fuel Rail Color: Anodized Black
Qty 1
$925.00
From Five-O Motorsports
Denso; 2008-2019, 5.7L, 4.6L, V8, Sequoia, Tundra
Part Number: 23250-00150, (12349) (12350) Tundra Sequoia 5.7
Options
EACH 750cc
Qty 8
$800.00
From Racetronix:
Bulkhead, -8AN to 10mm Barb, BLK
Qty 2
$11.68
Fuel Tube, 120 x 10mm, Black
Qty 2
$3.19
Fuel Tube, 125 x 8mm, Black
Qty 2
$3.19
From Summit Racing:
AEI-15674 - Fuel Block, Y-Type, Aluminum, Black Anodized, Male -8 AN Inlet, Male -8 AN Outlets
Qty 2
$159.90
Vibrant Performance 28008
Qty 9
$142.11
Vibrant Performance 28808
Qty 3
$88.77
Vibrant Performance 28408
Qty 2
$49.18
Vibrant Performance 28908
Qty 1
$24.59
Vibrant Performance 28976
Qty 1
$14.59
Vibrant Performance 28978
Qty 1
$15.59
Aeromotive 15610 - Aeromotive AN O-Ring Adapter Fittings
Qty 2
$49.90
EAR-AT100194ERL
-6 Fuel Pressure GA Adapter
Qty 1
$17.04
VPE-18968
Hose, PTFE, Black Nylon Braided, -8 AN, 10 ft. Length
Qty 1
$75.99

 

Wow, that's pricy.

 

Some of these fuel mods seems a bit unnecessary unless you’re running a +5 psi pulley and sending it down the drag strip every weekend, or making frequent pulls from 0-120. But that’s just my dumb opinion, and humble income speaking.

 

It is definitely overkill for now.

 

Hoping to get some time to upgrade the internals this summer, now that I have all the parts ready to go.

 

Nice! What compression ratio?

 

9:1

 

update...

Well…It needs a re-tune. Alex said the present tune is 90% of what he expects.

If I drive like an old man (I do), then this tune is OK. However - I want it ideal.

650 injectors are @74% at WOT. this is good
MAF is smooth. this is good.

Bad:
AFR’s don’t drop below 11.4
AFR bumps to 13 @ 4200rpm. Not good.
The cat protections thing is messing with the AFR.

So…he is fixing all that.

should be done later today....Can't get over to Tomball till Wed.


Life is still good.