What have you done to your 2.5 gen Tundra today?

Thanks. I was just at the scrap yard today too. Would've tried to snag one.

 

No. 4Hi flashed for quite a a while.

 

There’s a 2WD light? I don’t think I’ve ever seen it.

I’ve noticed this of I don’t straighten out the wheels and let off the gas for a second or two.

 

Just looked at it and enjoyed the sunset

 

The FRAC Harness is powered by the Head Unit’s ignition power circuit through the harness itself. So unless the ignition is on, the FRAC circuits can’t physically draw any power.

If the front camera is installed as recommended, it is powered by the same ignition source via the FRAC cam power lead. So it will also draw zero amps when the ignition is off.

Some guys have connected their front camera to a constant 12v source. I don’t recommend this approach. If this is done, then there will be a constant low current drain on the battery. This can cause issues over time.

Not sure how yours was wired, but i would check that.

I have helped a couple guys resolve some power issues where the power lead from various mods had been pinched to the chassis during re-installation. If a power wire insulation is not damaged enough to short out immediately, then over time with normal road vibration the insulation will still gradually wear down. Initially there may not be enough continuity to blow a fuse, but it can still cause excessive power drain until the time it fully shorts out. Those are the hardest problems to find. So I would inspect all modded wiring carefully.

 

I’d be interested in understanding any “weird” issues that may have been caused by the FRAC Harness. Quality is very important to me and I fully test every harness before it is shipped out. That said, problems can still arise so I also work hard with anyone having technical issues in order to resolve them.

 

Couldn’t wait so last night I insralled the rear EKE seat covers. Great fit and look in my opinion. Hardest part was getting the head covers on. Ended up taking them inside to let them warm up a bit before pulling them on.

 

My first wheeler was a Timberwolf 250 and then I inherited my dad's '93 or '94 Warrior. I had a lot of fun on that thing for a few years.

Here's my friend and I being retarded.

 

I do understand that. I have no complaints. You have great product and I like to support small business.
For me, if something doesn’t work or I don’t like it, I just replaced it with the other product till I like it.
That’s why I had 3 different kinds of suspension sets on my truck
Give me your address and I will send the harness back to you for your investigation purposes.

 

Do you have a link for these? I am looking for seat covers for my 2019 tundra. The ones I got off Amazon fit poorly!

 

Yea - here it is!

$230 EKR Custom Fit Full Set Car Seat Covers for Select Toyota Tundra CrewMax 2014 2015 2016 2017 2018 2019 2020 2021 - Leatherette (Black/Gray)

https://www.amazon.com/dp/B089W5Y7MM?ref=ppx_yo2ov_dt_b_product_details&th=1

 

Someone 3d printed these little window tabs for me years ago. Finally got around to installing. Not sure how long they Will last on logging roads but they work for now.

 

Installed EKR seat covers and 13 inch Tesla style radio from Phoenix Automotive.

 

Only had mine in a day, but I love them so far! Couple people I showed thought I had leather installed haha! You happy with yours too?

 

I love mine. The only thing I dont like or have to get used to is how cold they are when I try to leave in the morning with out warming up the truck.

 

can you send the link for the seat covers? i cant find the red like what you have

 

Funny, I thought the same thing this morning, but I can get over that for the look they add!!

 

Look up in the window a few posts - I sent it earlier today

 

EKR Custom Fit Full Set Car Seat...

$230 EKR Custom Fit Full Set Car Seat Covers for Select Toyota Tundra CrewMax 2014 2015 2016 2017 2018 2019 2020 2021 - Leatherette (Black with Red Piping)

https://www.amazon.com/dp/B089W5RH76?ref=ppx_pop_mob_ap_share

 

These really fit that well...? I've had them in my cart for a couple of months and haven't pulled the trigger because of some pictures I've seen of them fitting loosely (on the back seat mostly). I'm sure a lot of it has to do with the installation...?
I was thinking this would be a cost effective way to add seat heaters, as I don't trust myself to take off and re-secure my factory cloth seat covers.

 

I say do it. I was the same way they were on my wishlist for a few months before I did it. My backseats fit snug and are not losse at all. I installed mine while it was cold and didnt have to do any extra pulling or stretching to get them to fit right.

 

How do you like the radio??

 

They fit great. I did mine cold as well and thought the fit was pretty impressive considering cost. I am not sure I would put heaters between them and the original seat though, but I don;t know much about it.

My backseat was a little loose, but once it heats up here in MA I will adjust accordingly. One day soon it will be hot again...

 

Thanks for the feedback guys...that was the push I needed!

 

Hah no problem! I figured worst case even if it wasn't a great fit, its still WAY cheaper than Katskins or some other custom covers out there...Plus it's always fun to be pleasantly surprised by something you don't have high hopes for!

 

where is the write up for this?

 

How to: Customize your Toyota's Entune Audio Display with a Picture or Image - YouTube

 

Painted TRD satin black and found a home for it.

 

the video taco-spike posted isn’t the one I watched but it’s the same info. the only difference is the one I watched the guy said to make sure to capitalize the first letter of every word when making the two folders. I just used a picture I found on google but you can even do home photos. Hope this helps.

 

I am looking to replace the P D N thing to the left of the shifter, any idea what its called?