Autoloc auto window up and down project

shawn474 · Jan 5, 2022

Uhhhh.... said: ↑

Do you have the low or high module?
Click to expand...

I have the low version

102dalz · Jan 7, 2022

You need one of these at every switch? OR, do they only work from the driver's switch set?

Tundyjo77 · Mar 10, 2022

If installing for just front windows, do you install in passenger side or put both in driver side?

jamestada said: ↑

Hi All,

Just completed this install on my 2020 Tundra TRD Sport. Stock only had driver side auto down so I've installed on ALL 4 windows. Installation is a breeze.

Here is the set I purchased:

$80 AutoLoc Power Accessories 9863 2 Window One Touch Up And Down Window Unit

Autoloc 9863
The instructions it comes with are horrible, but the same company has the pdf (autwc1000.pdf) attached to this post on their website.

A couple tips before getting into the wiring:

If you've got some skinny hands, you do not need to remove the door panel to complete the install. Just use a trim removal tool to pry the switch module off the door.

The driver's door has a ground wire going to it, all other doors do not. So for the ground wire from the Autoloc module, you must ground it to the door. There is a bolt that is visible after you remove the switch module. If you can't get to it, you'll have to remove the door panel.

Wiring:

Front - Driverside

Cut: LIGHT BLUE and BROWN

Autoloc BROWN -> Switch LIGHT BLUE

Autoloc GREEN -> Door LIGHT BLUE

Autoloc WHITE -> Switch BROWN

Autoloc BLUE -> Door BROWN

Autoloc BLACK -> Tapped to Door WHITE/BLACK

Autoloc RED -> Tapped to Door PINK

Front - Passenger

Cut: RED and BLACK

Autoloc BROWN -> Switch RED

Autoloc GREEN -> Door RED

Autoloc WHITE -> Switch BLACK

Autoloc BLUE -> Door BLACK

Autoloc BLACK -> Grounded to door

Autoloc RED -> Tapped to Door BLUE

Rear Doors - Both are the same

Cut: RED and GREEN

Autoloc BROWN -> Switch RED

Autoloc GREEN -> Door RED

Autoloc WHITE -> Switch GREEN

Autoloc BLUE -> Door GREEN

Autoloc BLACK -> Grounded to door

Autoloc RED -> Tapped to Door YELLOW

Rear Window

For the rear window, there is no power supply there. You'll need to bring it to the auto up/down module. I used the power that is going to the rear door that you tapped into for the door.

To get to it, remove the bolt holding down the seat-belt, then remove part of the weather striping from both front and rear that is holding the lower trim piece and pry it off, it is held on by trim retainer clips.

Then simply use a multi-meter to figure out which is the constant power. You'll need the truck to be turned on.

Remove the rear passenger side seat, there are four bolts holding it down. I just leaned the seat forward instead of pulling it all the way out.

You'll see a wire loom going into the rear cab wall with two wires. From here it's wired the same way as the rear doors.

Cut: RED and GREEN

Autoloc BROWN -> Switch RED

Autoloc GREEN -> Door RED

Autoloc WHITE -> Switch GREEN

Autoloc BLUE -> Door GREEN

Autoloc BLACK -> Grounded to door

Autoloc RED -> Brought from rear door.

Click to expand...

Tundyjo77 · Mar 17, 2022

jamestada said: ↑

Hi All,

Just completed this install on my 2020 Tundra TRD Sport. Stock only had driver side auto down so I've installed on ALL 4 windows. Installation is a breeze.

Here is the set I purchased:

$80 AutoLoc Power Accessories 9863 2 Window One Touch Up And Down Window Unit

Autoloc 9863
The instructions it comes with are horrible, but the same company has the pdf (autwc1000.pdf) attached to this post on their website.

A couple tips before getting into the wiring:

If you've got some skinny hands, you do not need to remove the door panel to complete the install. Just use a trim removal tool to pry the switch module off the door.

The driver's door has a ground wire going to it, all other doors do not. So for the ground wire from the Autoloc module, you must ground it to the door. There is a bolt that is visible after you remove the switch module. If you can't get to it, you'll have to remove the door panel.

Wiring:

Front - Driverside

Cut: LIGHT BLUE and BROWN

Autoloc BROWN -> Switch LIGHT BLUE

Autoloc GREEN -> Door LIGHT BLUE

Autoloc WHITE -> Switch BROWN

Autoloc BLUE -> Door BROWN

Autoloc BLACK -> Tapped to Door WHITE/BLACK

Autoloc RED -> Tapped to Door PINK

Front - Passenger

Cut: RED and BLACK

Autoloc BROWN -> Switch RED

Autoloc GREEN -> Door RED

Autoloc WHITE -> Switch BLACK

Autoloc BLUE -> Door BLACK

Autoloc BLACK -> Grounded to door

Autoloc RED -> Tapped to Door BLUE

Rear Doors - Both are the same

Cut: RED and GREEN

Autoloc BROWN -> Switch RED

Autoloc GREEN -> Door RED

Autoloc WHITE -> Switch GREEN

Autoloc BLUE -> Door GREEN

Autoloc BLACK -> Grounded to door

Autoloc RED -> Tapped to Door YELLOW

Rear Window

For the rear window, there is no power supply there. You'll need to bring it to the auto up/down module. I used the power that is going to the rear door that you tapped into for the door.

To get to it, remove the bolt holding down the seat-belt, then remove part of the weather striping from both front and rear that is holding the lower trim piece and pry it off, it is held on by trim retainer clips.

Then simply use a multi-meter to figure out which is the constant power. You'll need the truck to be turned on.

Remove the rear passenger side seat, there are four bolts holding it down. I just leaned the seat forward instead of pulling it all the way out.

You'll see a wire loom going into the rear cab wall with two wires. From here it's wired the same way as the rear doors.

Cut: RED and GREEN

Autoloc BROWN -> Switch RED

Autoloc GREEN -> Door RED

Autoloc WHITE -> Switch GREEN

Autoloc BLUE -> Door GREEN

Autoloc BLACK -> Grounded to door

Autoloc RED -> Brought from rear door.

Click to expand...

Thanks for the post I bought the AutoLoc 1000 model but your wiring instructions were Spot on. Saved me Hours! Works Great on My 21 Limited Tundra !!

Log in or Sign up

Welcome to Tundras.com!

Autoloc auto window up and down project

#271
shawn474 Lego connoisseur

#272
102dalz New Member

#273
Tundyjo77 New Member

#274
Tundyjo77 New Member

Products Discussed in

Log in or Sign up

Useful Searches

Welcome to Tundras.com!

Autoloc auto window up and down project

#271 shawn474 Lego connoisseur

#272 102dalz New Member

#273 Tundyjo77 New Member

#274 Tundyjo77 New Member

Products Discussed in Entire Site Forum: 2.5 Gen Tundras (2014-2021) Thread: Autoloc auto window up and down project

#271
shawn474 Lego connoisseur

#272
102dalz New Member

#273
Tundyjo77 New Member

#274
Tundyjo77 New Member

Products Discussed in