What have you done to your 2.5 gen Tundra today?

This is what you want to use.

$24 303 Products Aerospace Protectant – UV Protection – Repels Dust, Dirt, & Staining – Smooth Matte Finish – Restores Like-New Appearance – 32 Fl. Oz. (30313CSR)

https://smile.amazon.com/303-30313-CSR-Aerospace-Protectant-Trigger/dp/B00KN0UOEE

 

Got a screamin deal on some Icon billet uniball UCAs. Getting installed tomorrow. I gave em a quick once-over.

 

Finally swapped some quality lights in for ditch lighting. Can't ever go wrong with some Plashlights lights.

These puppies are super low profile, saltwater rated, dupont coated, and pump out 2600 Lumens. Yeah they'll light up some ditches. Hooked em up to my strobe switch so I can use them for emergency flashers (10 different patterns).

 

AJT Steering wheel trim arrived today, now i'll have to find a moment to sling these on!

 

That bumper light bar though..

 

I just got shipment confirmation for mine, totally stoked.
Already did the vent rings and knobs
just ttrying to find the factory black stereo /center console piece to truly finish near full black out of my interior

 

Replaced the shiny pieces with the new Black from AJT Design and they are great. Easy install just be careful and gentle with the little screws. Also,, make sure your torx tool is in alignment.

 

Yeah, i am stoked too! I have all his stuff, just not much into painting, so i go the easy route, ha ha. I ordered the OEM center surround, spendy but nice to eliminate that silver!

*Edit: P/N if anyone is looking around for the black instrument panel/trim: 554050C020C1

 

Looks good… what about the shiny Toyota emblem on the wheel? Plans for that?

 

Don’t know yet???

 

I bought the one off Ebay that just goes over the shiny T on the steering wheel,

The black OEM , is it matte finish or shiny or ???

 

the diagram for that part is the worst, does it replace this ??? the silver around the stereo and enviromental controls ?

 

I do not think you can get a Black steering wheel Toyota symbol?? AJT used to make one that covered the chrome one but they can not do that anymore. I sent an email asking if they had one on the floor I could have but no response!! I am sure they come off. If I get that ambitious I can take it off and scuff it up and paint it??

 

www.plashlights.com

 

Flea bay and someone on fb marketplace tundra parts has em ,

 

yeah, all over

Steering Flat Black Emblem Overlay for Steering Wheel Fits | Etsy

New Steering Wheel Emblem Overlay Toyota ( Tacoma Tundra 4Runner) OEM | eBay

toyota steering wheel emblem overlay - Google Search

Steering Wheel Overlay – Taco Vinyl

Toyota sent out cease and desist letters to a lot of people. Can't even send out stock they had, probably had to destroy them?

 

There are some on ebay that you can get though. Otherwise, it is just held on with a few plastic rivets. Comes off easy and a few folks have painted it.

 

Assuming this means the coating is failing on them? Did N-Fab step up and replace them?

 

Your a year into these, how are they holding up so far?

 

I meant to have OEM in there. Fingers doing tricks on me again. Ken

 

Color matched door handles and mirror caps. Finally! It creates such a smooth, classy look. Probably more noticeable on another color, like white or cement, but I still think it’s a tasteful touch with the MGM.

Before




After






I am giving some very serious consideration to peeling the black vinyl wrap off of the B pillars. There’s paint under there, and I think it will look so much better. Is there anyone who would talk me out of that?

 

Just ordered an overlay from one of the ones pointed out down there somewhere. So that took care of that.

 

I know someone else on here that took there pillar tape off, it looks good. Try the search function and I am sure you will find it.

 

It had flat spots in it and looked like crap. They said go through the vendor. The vendor wanted me to buy another set, pay shipping both ways, and use the box to send them back. I said no. Why waste money for that set to do the same thing.

 

Steering Wheel Emblem Removal for Painting | Toyota Tundra Forum (tundras.com)

 

D/S grab handle!

 

Yes I have seen that. Eight or eleven spot plastic welds is to much for me to possibly mess those up. Fat fingers and plastic weld spots do not make for an easy 1234 process. As much as I would like to take it all apart and paint it the proper way the overlay will be the ticket and it shall stay covered until whenever??

 

Here's the overlay for the Steering wheel, far easier than removal and painting
bought it for $15 on ebay however the seller doesn't have it listed anymore so not sure if
maybe it was an item bought from somewhere else and he was just reselling

 

Bought it new in 2017

 

Do you have a crew max with a column shifter?