Lomax Tonneau cover, so far all good

The Stance folds up against the rear window and attaches to a couple anchor points located on the roof...the original lomax only folds 2/3 of the way, but can removed without any tools!

 

I have the stance. It only comes in the bed liner finish. Looks great. Love the cover. The stance fold up exposing the entire bed (by propping up against the back window. Never comes in contact because there are support rods). As opposed the the other that folds twice and to use the entire bed you have to remove the tonneau from the bed of the truck.

 

thanks for the feedback. I called Agri-cover yesterday for some more info and ended up ordering one. I definitely like the bed liner finish over the others. I have the bed rails so will check back if I have any issues.

 

I have the bed liner looking finish on mine. Make sure they send you the correct pieces for your truck. I received side rail for Ram 1500 initially and took two diff phone calls to Agri-Cover to get the right part. Also, if you have the oem bed divider, it will work with it but there are couple of tricks to it.

 

Can I get a top view pic of the cab to see where you guys are mounting the brackets that hold the cover upright?

 

Thank you sir!

 

These look really nice. Lot of bakflips around my area. Where is go to site to purchase?

 

Not to steal the question but, I got mine straight from the dealer -AgriCover.com Very helpful and can answer all your questions. I did have some local shops who would order AND install at no additional charge which might be worth it.

 

I just got a Lomax cover installed on my 2021 tundra. Also installed tundra side rails, Adarac rails, towers, bars and Yakima bike racks. The cover, towers, rails, and bars are made by Agri-Cover. I just bought the truck and didn’t have the factory tie down cleats in the truck when they installed the system. I was going to try to put the cleats in the factory rails but it looked like there isn’t enough room above the cleat so the cover will hit the cleat. Do the factory cleats still go into the factory rails ?

 

Here is a picture of the cover and racks

 

They do, but it's a tight fit. Pretty close to the tonneau, but they do clear.

 

Are the cleats really that useful being so high in the box.

 

They are still functional but it’s a tight fit. This is the OEM rails and cleats.

 

I figured it out. Like you said, you have to turn the connector upside down and you will have to find the exact spot to install the connector. I can take a picture of my setup later today and post it.

 

My BakFlip MX4 has been sheer garbage. Leaks in multiple areas, well beyond the typical corner of the bed leaks. Several pieces have broke off in less than year and the cover gets very little use.

I can attest that BakFlips customer is nothing less than atrocious. I sent them over 30 pictures as per their request and still got nothing resolved. Multiple calls were made as well and they could care less about the customer once the cover was sold.

 

Here it is. Connectors upside down.

 

I installed the tie downs on the rails. They could only slide in one way. They just fit. I had to remove the clamps and the stops at the top and reinstall but it all worked out.

 

How do you like the rack with the hard cover?
I love my Lomax and considered getting the adarac but I know the pro tall straight rack is the only one that lets you open the cover. Curious what your doing with the shorter bars? Taking them off to open the cover or just keeping the cover closed all the time?

 

I use it to haul my bikes when I am towing my trailer. I can access everything I need from the tailgate. After camping season I will remove the towers, bars and bike racks. Then I can open the tonneau cover if I need to haul something taller.

 

When u open it all the way up
Does the remaining bottom piece protrudes out to the front bed rail or sits flush?

 

This piece

 

Caved and finally picked up a Lomax trifold, not the stance. Installed it last night and noticed this this morning. I torqued all clamps to 25 foot pounds, as per the instructions. Both deck rails are now bent downwards slightly. Are you guys seeing this on your trucks?

Nervous to uninstall and find that the deck rails and the box panel behind them are permanently bent.

 

Agri-Cover customer support says they've never seen or noticed the deck rail roll like that. Advised taking the torque down to 20 foot pounds. Improved but not by much. Still curious what it looks like on your trucks.

 

Which kit are you guys buying if you have the oem bed rails? I'm not sure if I should buy the tonneau with or without the deck rail system.

 

The clamps that come with the cover fit into the OEM rail system. The clamps clamp the the lomax rails that the edge of the cover sits onto. You need the cover and system that fits the Toyota Tundra. I have rails also that fit above the sides of the box so I can bolt towers and bars on.

 

Thread has great timing. Been looking at hard cover options for my bed. Normally I do camper shells but kind of want to try something different but was becoming kind of disheartened by the negative reviews that almost all folding bed covers seem to have. Well that and I don't want to lose use of the roll down back window.