What have you done to your 2.5 gen Tundra today?

Washed the road grime from trip to Floyd Va. Ordered Fob case from AJT. Delivery man left my Scoshe phone mounts. Yeehaw. Great weekend so far.

 

Wired up my Rigid ditch lights this afternoon. I did use a premade wiring harness off ebay but ended up customize it quite a bit. Also thanks to a couple threads on here, I found out about a light blue wire to tap into for the dash light circut for including in a CaliRaised oem style switch. It's backlight is really bright but looks clean.

Looking forward to using these when I find a place to camp at 12am... which always ends up happening somehow

 

WoW... this is SAVE IMAGE AS material! What wheels are these?

 

Thank you! They are Fuel’s Sledge D596.

 

Finished up inside of my truck today, added a few outside things too. A/C vents blackout. radio noobs black out, decals, radio logo, TRD emblem on hood bulge, tailgate decal.
Washed the Lexus, it’s cookin here today.






And now I’m doing this


Have a Save weekend Tundralights

 

That’s a cool looking dog.

 

Glad to hear you got it repaired over having to replace. Unfortunately all 3 of mine are cracks almost length of windshield.

Go get em with ur face, I don't own a dump truck so I'm all for it. Since I got a class A CDL and my job knows I'm nice behind the wheel, my job usually appoints me to drive the bigger trucks and machines. Where I work there's tons of trucks and machines, like a grown up playground. Just my department got tandems in an auto Western Star and manual Mack. Plus we got a tanker and various machines like backhoes, loaders, and minis. Guess u can say I'm a jack of all trades, master of none. I know a little bit about a bunch of stuff, just enough to be dangerous. Anyway, my point was I own none of them, just a driver/operator so have at it with the face stickers. I'll keep an eye out for them in my travels lol.

 

I just ordered some OEM ones.
Left - 692060C040
Right - 692050C040

 

Installed the BAM 8" Standard exhaust thanks @dirtydeeds very solid built exhaust and smooth install. I took my time and put another coat of paint on the BAM and after removing the axle turn down section for the resonator install painted it again as with the 7" lift can see the exhaust around the axle.

Debated on whether I would bother installing the resonator or no , but drove it with and without and WITH is the right answer for our needs...no drone, quiet in the cabin until you wake the beast then you can hear the deep tone / throaty sound!

I just want to go back out and rev it up all night lol. I would post the video but phone is missing much of the deep tone and growl it produces.

 

Where did you pick up your grill badges?

 

Do you have the sub wired for 2 ohms?

 

I've seen them on eBay.

 

I usually don't park inside the garage, but I will deflate each time I drive in to attach / remove the RTT (at least until I get rid of the RTT).

 

https://www.ebay.com/itm/224124739861

 

Yeah, the woman went a little nuts when this whole Covid thing started.

 

if you're talking about the door handles, I got them off carparts.com. They're for a 2017 sequoia.

 

Ohm....let me see.....lol. I just followed the directions from the tech 12volts site. So, whatever that is.

 

What tail pipes are you running?
Is it the trd?

 

Yeah, I plan to get the rest of the system also. You'll get more out of it if it is wired for 2 ohms. I don't remember what it comes as out of the box, it's just a switch on the sub.

 

Hey Hightide! The BAM standard 8" system from Dirty Deeds Industries (http://dirtydeedsindustries.com) just bolts between the cats and the over axle tail section I think you're asking about. For the install just takes a 12mm, 14mm and a hammer (to help with sliding hangers outta rubber mounts). It's just the factory tail section that's been torchered short after the axle turn down with a TRD tip on it there pointing mostly towards the ground. All painted with high heat flat black. Like the look with the lift and all. Always ran duals on prior trucks but am a big fan of this setup. I was going after the TRD pro exhaust until the research on Tundras...to be honest I've not heard the PRO system in person but I'm tickled pink with the sound here and it's stainless and less $. Cheers!

 

No switch on the sub I got from him. These were the directions I followed....

 

Thanks!

Yeah, I have the TRD system but want to go with Bam mids.
I did notice a bit of low end losss with the trd system but like the look.

 

Yeah, mine were the same. There should be a switch on the back of the speaker itself, chances are it is 2 ohms already. You can verify with James. I asked him directly what it should be set to.

 

3psi doesn't break the bead?

 

What did the full kit cost from boss?

 

This is funny. I saw this on the net tonight. Immediately changed my screens then later saw this forum. Great timing i guess. I have a 2014 SR5 TRD package and I did this no problem. I had to try 2 usb's though. Truck didn't like the first usb. Make sure pics are 800x480 and the folders are labeled correctly. displayoffimage and startupimage. Works perfectly!

 

I just picked up the same kit from wheelers off-road but with spc ucas included for 1770