My DIY build progress...mistakes included.

https://www.amazon.com/dp/B07J4D6QN1/ref=cm_sw_r_cp_api_i_6ygECb8BVR82K

 

Edit: I followed the link, and it now goes to a Chevy organizer, so I deleted the link. I guess they don’t have the tundra one listed right now. It was by mictuning and was $10.

 

Here is the new steering wheel cover that my gf sewed on. It is by Loncky.


Here is the Defender rack by Smittybilt that I customized and installed.
Some of you will say it’s too low, some will say it’s too high. Any lower and I couldn’t access the bed or open the bedcover, any higher and I couldn’t lift stuff high enough to put in. Plus, I didn’t want a “ladder rack” utilitarian look. I felt this was more stylish, and will fit under the sport bar (nonfunctional roll bar) I plan on installing.



Since you can’t see the subwoofer behind the seat, I am posting a photo from before I installed it. It is a 10” shallow sub with a built in amp...by Cerwin Vega. It also has a remote to control the gain.

 

Leveling kit installed.

 

Where did you order what parts? Like it.

 

Here is the write-up.

https://www.tundras.com/threads/110v-outlets-in-bed-and-console-write-up.37500/

 

Where did you get the 3rd brake light? Are you happy with it? I have read bad reviews about all of them because of poor quality and they always leak

 

I got it on eBay. No leaks and very bright.

 

New ESP storage plus a photo of my Smartliner mat I hadn’t shown yet.

 

I guess I was looking for the brand to make sure I do not buy the cheap junk they have been selling. Would you happen to have that info?

 

It won’t let me click the link because it’s been too long, but this it what the post looked like.

 

New wireless charger. $25 shipped.

 

I got rear ended recently, and the only damage was to the tail light...so I decided to upgrade.
I usually get smoked tails for darker vehicles...but since we move a lot and I never know what the laws will be where we move, I went with clear. Unfortunately, clear has an almost white outline when mounted. Instead of returning them, since I really like them, I wrapped over the white part with matteblack vinyl. I like how they turned out.

 

Looks killer who makes these?

 

Anzo

 

Link for the charger?

 

$23 Wireless Charger,POLMXS 10W Wireless car Charger Charging pad Fast Wireless Phone Charger pad Andriod Cell Phone Wireless Charging mat Galaxy Note10/S21/S10/S9/S22(C3)

https://www.amazon.com/dp/B07GZZX37F/ref=cm_sw_r_cp_api_i_5owIEb585JNCE

 

Very interested in how you converted the AJT Design Case to fit both the key fob and key. My tundra keys are the same as yours and I would love to do the same.

 

It wasn’t easy. Haha.
I think I explained it somewhere. Let me find the link.

 

Guess I didn’t do a write-up on that one.


I used a soldering iron and several types of blades to make the notch for the key, and to remove the original key housing.
I cut the key to the proper shape with a cutting wheel, and then wrapped the end with heat shrink to shield the electronics from it.
I also had to melt out a space in the backing and trim the main housing so it would still close with the transponder placed inside.
I'm sure it will be easier the second time around. I’ll do a write up in a couple of weeks when I get the case for my second key.

 

Greatly appreciated !! Thank you much !!

 

I installed my modified tail lights after blacking out the outer edges.